Jump to content
SAU Community

Recommended Posts

Hi everyone,

First post from a long time reader!

I'm currently in Japan, and will be for another 10 months or so. It has been a dream of mine to purchase an R32 GT-R for many years now. My master plan is to purchase one here, drive it within Japan for the next 10 months, and then import it back to Australia (for everyday use) when I head back.

Stuff I have worked out so far:

Can't import R32 GT-Rs made between July 1991 and May 1992.

Post May 1992 models would be preferable due to already having side-intrusion bars fitted.

The main thing I am not sure about is to what extent the car must be returned to factory condition upon importing it into Australia. For example, the majority of R32 GT-Rs in Japan seem to have basic modifications such as aftermarket wheels, exhausts, suspension, steering wheels, 320km/h gauge clusters etc., unless I pay the premium for a completely stock one.

Taking into account that I would like to register the car with normal road registration, can anyone please tell me to what extent the car I import needs to be in factory condition?

Thanks heaps :)

Link to comment
https://www.sau.com.au/forums/topic/400545-purchasing-from-within-japan/
Share on other sites

The main thing I am not sure about is to what extent the car must be returned to factory condition upon importing it into Australia. For example, the majority of R32 GT-Rs in Japan seem to have basic modifications such as aftermarket wheels, exhausts, suspension, steering wheels, 320km/h gauge clusters etc., unless I pay the premium for a completely stock one.

Hello, Nice to meet you and good luck with your search.

Are there many stock R32 GTR's left over there? It was very hard for me to find a completely stock R34 GTR and I wanted a particular colour and spec. And the clean close to stock ones over there cost just as much as they did over here in Aus (and thats before you even got them on to the boat + compliance - etc).

There are many which are around 95% stock, with only an aftermarket exhaust for example, but the completely stock ones are few and far between. They are at least double the price of one with a pile of mods, seemingly regardless of mileage. I'm not really too fussed on the one I buy being 100% stock, I just don't want to run into trouble when the time comes to have it complied.

Unfortunately I can't seem to find any definitive information on what is allowed and what isn't. I've read that compliance places often say the brake pads need replacing for example, and that you have to replace them with original Nissan pads. Stuff like this is really turning me off the whole procedure, if only I knew what parts have to be stock, I would be much better off. I might try contacting an importer about it.

Someone like Kristian/Iron Chef will give you a more accurate answer but I believe you must own the car for a minimum 12 months before you can privately import the car (which is easier/cheaper then importing as per usual). Obviously the good thing about doing it this way is that you are not constrained by what is and isn't "eligible for import".

Just something to think about.

Thanks for the advice everyone!

I have one more question about the necessary side-intrusion bars if you don't mind :)

If I purchase an 89/90/91 model over here, and then swap the doors with those from a later model while I am over here, would it be ok? I'm just assuming it would be much easier/cheaper to buy second hand doors here, rather than paying a compliance shop to find and fit them in the Australia.

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...