Jump to content
SAU Community

Recommended Posts

Awesome guy and quality products too !!

Thanks mate!!

Just an update:

-Both sets of brake pads are sold

Still heaps of good parts for your rb26 and r32 gtr left.

Cheers.

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

hey mate did the wind visors sell if not do they come with clips? my last pair ripped off on the freeway fml

hey mate did the wind visors sell if not do they come with clips? my last pair ripped off on the freeway fml

Hey Bud!

Yeah unfortunately they are long gone!! they didnt come with. sicaphlex (however its spelt) or 3M car double sided tape.

Guys have had em at over 180k's and no problems. My mate has oem clip ones on his evo and they still rattle around etc at like 80 or so, so im pretty iffy about all that.

cheers

BIG FAT BUMPPPPPPP.

help me fund my next car!!!!. heaps of parts that are tricky to find, items to help u with defects and good spares.

Get rid of those exposed pods and go to an OEM airbox with snorkel. proven to flow 350awkw on a gtr!!

CHeerrs

BIG FAT BUMPAGE: THESE NEED TO GO!!!! THROW ME SOME PRICES!! SOME THINGS ARE NEG!!!

Torque splitter now available: Buyer pulled out!!!

Standard Airbox w/Snorkel in perfect condition w/Blitz panel filter - $300, filter is in packaging brand new rrp is $80

3" Silicon pipes x 2 $10 FIRM EACH (just jap rrp $21)

TRUST R32 gtst/gtr rear pods (lined up and test fitted to a 32 Gtr - have been in a box since i bought them) $75, these go for $200 ish online. These are ready to Prime and paint and fit.

CF N1 boot lip, pefect condition was mounted on car but took off) bottom is dirty from double sided tape - $120

CF dual gauge 60mm A pillar holder 32 gtst, gtr, Greddy make - $150 BRAND NEW never fitted or anything

G-Rex Oil cooler with braded hoses and oil filter relocation, used for 7000km before i bought it, perfect condition $700

Nardi Leather steering wheel with black backing (awesome condition used briefly) - $150 rrp is $350

R32 Gtr guard liners, Passenger side has a wear mark from rubbing tyres, could be plastic fixed and reused easily (defect if you dont have guard liners these are hard to find now - great condition otherwise, removed carefully) - $150

RB26 Twin turbo pipe awesome condition w/spare end side rubber pipe - $150

R32 Gtr intake side intercooler piping (yes the big OEM rubber covered pipe awesome condition) - $150

Cusco Driver side intercooler pipe (Painted properly in high temp paint for a stealth look perfect condition) $60

R32 Gtr rear mats, left and right + centre wrap over mat (hard to find, great condition and in 94 model styling) - $100

ON HOLD R34 GTR intercooler, brand new condition (did 5000km as was a new OEM part, previous owner was reversed into by ute, he replaced it with OEM new and then upgraded to larger for drag application) i never fit it however made a cover for the O2 sensor so that R33 and R32 gtrs can use it. few fins are bent but its in un believable condition. - $400

ON HOLD Race Pace adj cam gears (these are OEM made to last quality and are a stock look, proven reliability over durilium after market brands) bought for $358 will sell for - $300 never USED!

ON HOLD - R34 Gtr V spec dump pipes awesome condition off GTR SEAN - $250 or extra if you want me to high temp paint them.

Torque splitter 2wd/4wd with 10 settings between. awesome bit of kit, brand new in packet - $300 rrp $599.99

HKS shifter 12mm thread type to fit R34 GTR, comes with space to make it 10mm so that will fit any 5 speed nissan will fit. These are ultra rare these days. chasing $65. brand new, has box, spare stickers for top of the shifter depending on pattern and is WHITE.....

Going to try and update pics of everything tomorrow if i have time!!

Sorry to all the guys that havent got pics yet. all the boxes are up the back of my house mixed in with timber, construction stuff and other junk!!

have also been very very busy with work and had precious little time.

CHEERS!!

Apologies.

N1 lip is Gone!! please disregard this item in the above post.

thanks rb1994.

Have Pm'd everyone and emailed all pics to everyone that wanted them!

cheers

give us pics and details on hks shifter. what is required to make it fit late model (94)r32 & r33 gtr box?

cheers

Andrew

give us pics and details on hks shifter. what is required to make it fit late model (94)r32 & r33 gtr box?

cheers

Andrew

Hi mate.

Can get pics I'd needed. Literally go on to google type in hks white shifter. It's the limited ball type shifter. Comes with thread adapter and stickers for 5spd Nissan. The adapter is a brass fittin which attaches to shifter and then knob attaches to this.

NARDI steering wheel

and

TRUST rear pods

look to be Sold, being picked up tonight.. if buyer puls out these are up on the market again

UPDATE OF STUFF THATS STILL AVAILABLE: I'm Keen to move most of this stuff, most items are NEGOTIABLE: try an offer, worst i can do is say No.

Standard Airbox w/Snorkel in perfect condition w/Blitz panel filter - $300, filter is in packaging brand new rrp is $80

3" Silicon pipes x 2 $10 FIRM EACH (just jap rrp $21)

PENDING TRUST R32 gtst/gtr rear pods (lined up and test fitted to a 32 Gtr - have been in a box since i bought them) $75, these go for $200 ish online. These are ready to Prime and paint and fit.

CF dual gauge 60mm A pillar holder 32 gtst, gtr, Greddy make - $150 BRAND NEW never fitted or anything

G-Rex Oil cooler with braded hoses and oil filter relocation, used for 7000km before i bought it, perfect condition $700

PENDING Nardi Leather steering wheel with black backing (awesome condition used briefly) - $150 rrp is $350

R32 Gtr guard liners, Passenger side has a wear mark from rubbing tyres, could be plastic fixed and reused easily literally no damage (defect if you dont have guard liners these are hard to find now - great condition otherwise, removed carefully) - $150

RB26 Twin turbo pipe awesome condition w/spare end side rubber pipe - $150

R32 Gtr intake side intercooler piping (yes the big OEM rubber covered pipe awesome condition) - $150

Cusco Driver side intercooler pipe (Painted properly in high temp paint for a stealth look perfect condition) $60

R32 Gtr rear mats, left and right + centre wrap over mat (hard to find, great condition and in 94 model styling) - $100

ON HOLD R34 GTR intercooler, brand new condition (did 5000km as was a new OEM part, previous owner was reversed into by ute, he replaced it with OEM new and then upgraded to larger for drag application) i never fit it however made a cover for the O2 sensor so that R33 and R32 gtrs can use it. few fins are bent but its in un believable condition. - $400

Race Pace adj cam gears (these are OEM made to last quality and are a stock look, proven reliability over durilium after market brands) bought for $358 will sell for - $300 never USED!

ON HOLD - R34 Gtr V spec dump pipes awesome condition off GTR SEAN - $250 or extra if you want me to high temp paint them.

Torque splitter 2wd/4wd with 10 settings between. awesome bit of kit, brand new in packet - $300 rrp $599.99

HKS shifter 12mm thread type to fit R34 GTR, comes with space to make it 10mm so that will fit any 5 speed nissan will fit. These are ultra rare these days. chasing $65. brand new, has box, spare stickers for top of the shifter depending on pattern and is WHITE.....

Trust pods

and

Nardi steering wheel

Back on the market!!

New rules for items due to being f**ked around by a few twits taking up my time and energy.

If you wish to buy the item, I require a deposit **which is non refundable to hold the item (that way there is an incentive to actually follow through) otherwise i will sell to the first person who has $$ to pay me.

If you dont like that or your stuffing me around and i sell the item its too bad so sad. Dont stuff me around.

Please throw some offers around.

To those that are interested in POSTAGE or PICS please PM me and we can sort that out.

  • 2 weeks later...

BUMP THIS UP!!!

Going to do an updated parts list this weekend with pictures.

Alot of things are now up for grabs as have fallen through or become available again.

Neg on most things. looking to get rid of this stuff asap.

Also have the following to add in for a R32 Gtr:

Carbon fibre: (all made in Japan, from Matt Newera imports, Genuine Japanese carbon fibre NOT CHEAP CHINESE STUFF!!

-N1 Spats

-exhaust shroud/protector

-Intercooler ducts

- East bear, electric mirrors.

Prices and pictures coming this weekend.

Offer away on anything i have!

All PM's answered. Going to start a new thread on the weekend i think with an update of all new parts along with some well overdue pics.

Please look out for this.

cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...