Jump to content
SAU Community

Recommended Posts

I had an issue where when I was cruising for some distance my tune was running rich and fouling plugs. Around town was fine but any highway use it was playing up next day on cold start. I backed the map off only slightly on that fuel cell and it has fixed the problem. Just thought i would mention that sounds it could be the same

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

Definitely a possibility, if I was to pull the plugs after a failed idle when I start it how could I tell if they are fouled easily?

Actually the only times the car idled well was when we first put the injectors in, then it went to shit, and then I changed the plugs before the tune and it was shit after that, then came good for a week then went shit again.

Maybe they have just fouled up badly.

Edited by Rolls

Is ur fuel pressure stable? Ie has the pump been rewired to battery voltage?

Is 02 feedback enabled?

If u have the software or consult keep a close eye on inj duty when idle is good and when idle is playing up. Let me know the readings

Fuel pump is new and rewired to battery voltage, O2 feedback is enabled as well, just need to borrow a laptop so I can run consult again.

Does anyone know what the "Fuel Dumper" is? as I did not get this part when I bought my fuel rail, is it a dampener of some sort? Perhaps this could be my issue.

70105224.png

Seems like a misfire when cold, cannot figure out why though, really need to get a wideband in the exhaust to see if it is going lean/rich or if it is super rich at idle fouling the plugs.

Bummer because I have neither a wideband, nor a nistune license.

Hey, that's awesome. The country I am in cannot be typed in spelled correctly, because it gets replaced with what you see in my post above. Just for the fun of it, the country I am in is bordered by Greece, Albania, Syria, Iraq, Iran and Armenia, with coasts on the Black, Adriatic and Agean Seas.

And in some respects it is the sphinter of the universe!! Although I don't mind it. Sphincters are not all bad.

Am trying to make the kiln burner here work properly. I designed it last year, installed in February, and it hasn't worked properly since. Has in fact made the whole plant worse. It's my fault and it's not my fault. Bloody plant has huge issues. Given the huge issues I should have called the whole thing off instead of proceding. But I let optimism strike me, went ahead with it, optimism bailed on the deal and left me with a handful of poo. The goat lovers are also not very able to handle the subtleties of a carefully written performance guarantee, and refuse to accept that given that the plant is poo, it is not entirely my fault that my burner made it smell worse.

Rolls my idle sounds very similar to yours.

I idle at around 1400-1500 when cold and it hunts randomly and sits there missing until warm.

Once warm idle drops to around 700 and them every now and then hunts but does not miss.

If you take it for a drive when cold

As you take your foot off and coast you can feel it missing.

All goes away when warm

Hmm this morning it was much much better, I didn't drive the car yesterday at all so it must have been completely stone cold, still did a slight miss for 3 seconds then come good for 3 seconds but it didn't want to stall, just went from 1300rpm to 1000-1100rpm.

Tonight it was back shit again wanting to stall from 1300 to 400rpm.

I have my laptop back so I will plug in consult and do a dump of injectors/afm etc vs rpm when its cold see if it is an ECU or mechanical problem, I personally think it is fouling the plugs up from possibly too rich an idle.

Is ur fuel pressure stable? Ie has the pump been rewired to battery voltage?

Is 02 feedback enabled?

If u have the software or consult keep a close eye on inj duty when idle is good and when idle is playing up. Let me know the readings

Ok did a log when cold, when at 1200rpm the duty cycle is 1-2 and pulse width is 2.2ms, when it stumbles duty is 1 and pulse width grows to 2.5ms all the way to 3ms when it starts missing badly, timing changes from 30 to 34 when stumbling, acc duty increases slightly.

Stab the throttle and it goes back to 1200 and duty at 2, pulse at 2.2ms, starts to stumble and go up to 2.8ms etc.

Would this be as simple as just changing the cold start enrichment at 20-30c so it is slightly less rich? I'm going to buy a license next month so will have a fiddle then.

So I am guessing the cold start is just simply too rich

Edited by Rolls

Its possible. Bust never assume its too rich without having a wideband to tell u afr.

The timing doesn't seem right. It should not be at 30 degree's at idle. That tells me ur tps may not be setup correctly. Try dropping the tps back a tad ie: if its at .5 try .46

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Photo of manifold showing gate location? I mean, it's 6Boost, so we probably shouldn't be worrying, but always wroth knowing what the layout is. Plumbed back to atmosphere? Or into the dump?
    • Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
×
×
  • Create New...