Jump to content
SAU Community

Recommended Posts

I have been told by mechanic that I have a R4 Engine in my Skyline R33 S2

Thats the reason some of the wiring is different on this one.

I have a High Idle of 1000 RPM+ , I had a problem with Aircon in summer that If I would turn that on my car will just die.

So I was looking at some wires I found that MAF and AAC wiring are left as is and not connected.

I got two plugs spare that are not in use , I remember that they were connected in my old S2 ( that I sold :( )

can anyone tell me what to do with these one ? I've marked them with green color!

Any help will be highly appreciated

post-75024-0-58694300-1339385245_thumb.jpg

post-75024-0-11016300-1339385259_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/402253-where-do-i-plug-these-ones/
Share on other sites

Dev man

the guy said its running a haltech ecu but when i saw on left hand side its normal ecu with many wires cut

itsjust better to get rid of this engine and put a stock one

The engine is fine, its the engine management you need to sort out to see which one you have.... It may have a haltech as a piggy back somewhere?

BUT first thing i would do is get rid of the BOV as that is really not going to help your cause.... I put an atmo on my R34 for about 3 minutes before i realised it sucked! THEN sort out wiring!

  • 1 month later...

Follow the wiring from the motor in the Idle Air Control (IAC) valve on the rear of the inlet manifold & see if it's connected. I have a funny feeling the little red curly thing in the picture is the power wire for it, & it doesn't look connected. It just ends. As for the two female plugs, The brown one could be for the valve for the charcoal canister, which isn't there. The greyish looking plug could have been for the factory boost pressure sensor. Both of these are located in that area on my S2 C34, although the plugs are different shapes, the grey one is boost pressure sensor. Your best bet is to find someone with a stock R34, or even a dealer. Pretend your buying a car, lift the bonnet & have a good look!!!!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...