Jump to content
SAU Community

Recommended Posts

Yeah clubs are shit but all club are shit.

When you mix normal people with roided up beef cakes that bench press 20 kgs with everything to prove it tends to ruin your night alot haha. I've been out clubbing twice, once with my sister and her bf and someone was trying to pick a fight :S

I prefer pubs now anyways, can sit, have a beer and talk shit with mates. Not just bop, looking at ugly people haha.

ha lets just say jarrad is a little fond of birdbaths after a couple of drinks... pretty funny stuff.

OKaaaay :P

A story that may come out after a few beers I hope? Lol

When you mix normal people with roided up beef cakes that bench press 20 kgs with everything to prove it tends to ruin your night alot haha.

Yep pretty much summed the nite up. We were at a pub to about 12 -thats was fun, then went to finnegans and it was like WTF are we doing here...its the case of same sh*t, different weekend for newcastle clubs.

ha lets just say jarrad is a little fond of birdbaths after a couple of drinks... pretty funny stuff.

Thats pretty funny....what about a beerbath...

Edited by wedge_r34gtr

Haha yeah, such a shame ay. So glad I have a girlfriend haha. Don't have to try and sift through the hoe bags.

I just broke up with mine :(

But fark meeting anyone at a seedy club!!!

Pft screw clubs, let's all go for a WOT!

WOT?

Wide open throttle maybe?

Had a good night out tonight

Went to Anchors for tea then to Wests mayfield to play poker ( I was out early ) but then won on the pokies went to Wests at new lamb ton and won on the pokies again so basically a free night out with the wife

Edited by m.j.h

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...