Jump to content
SAU Community

Recommended Posts

No way benji, the track is heaps tiring specially in summer. I always get so f**kin drained!!

Will do mathew!

f**k yeah tank!

Ill get tired and the blood will probably give me a headache from hanging upside down in the Gravel trap for extended periods of time :woot:

And who you calling Mathew ya kent! :dry:

Yeh even the mecahnic was like FFFAAARRRRKKK when we got out of it, it f**king hammers now with the new plugs i cant wait to get a power run done i think i may have to call Mr DVS

I hear he is only doing Mazda 3's now?

:laugh:

Whats this "WE" business white man, i was leading the pack :woot:

U knw he was taking it ezy lol ZOOM ZOOM BOOM :woot:

next cruise looks awesome to, will be great cant wait for the 100km zone with duel lanes will make for some awesome photo's

You will have brakes fitted by then?

Most likely before the nats, just waiting on the rear pads to come in!

Brake install will be slotted rotors, changing fluids, new hoses for calipers, new pads, and new hardware kits.

You will have brakes fitted by then?

LOL, why is it so hard to have brakes fitted,

1. call GSL rally sport

2. wait 3 days for pads to arrive

3. call decent mechanic book car in

4 have pads installed.

works 90% of the time 100% of the time

this goes for all the other parts to just add them to step 1 and 2

Edited by T4NK

Turns out I can stay with emmas dad :) cheers mathew ya sweetie!

Some flamin mongrel just parked over my driveway when if he drove 5 metres forward he'd be off it in unlimited parking.

We wrote a note :P

Just have to look out for kangaroos tank. Nearly totally my car :)

I saw the prick with 5 metres to spare, Martin didn't see him I was going 100 and had to go completely on the other side of the road to miss him by around a foot or two.

Butt clenching moment haha!!

LOL, why is it so hard to have brakes fitted,

1. call GSL rally sport

2. wait 3 days for pads to arrive

3. call decent mechanic book car in

4 have pads installed.

works 90% of the time 100% of the time

this goes for all the other parts to just add them to step 1 and 2

QFT

Just have to look out for kangaroos tank. Nearly totally my car :)

I saw the prick with 5 metres to spare, Martin didn't see him I was going 100 and had to go completely on the other side of the road to miss him by around a foot or two.

Butt clenching moment haha!!

I would have seen it if it came through the windscreen

Your plugs should not have clogged themselves up that quick. I suggest you give a jez a ring to run some diagonistics.

O2 sensor voltage can be checked with the afore mentioned diagnostics or pull em out and if there fouled like your plugs then there Probarly stuffed.

dear heavenly father. twin turbo be thy power, thy kingdom come, tuning will be done, as in aus as in japan. bring to this day four wheel drive and praise our power figures and forgive thoes with less power than us. keep us safe from the cops and deliver us from the under ground, for the GTR32 33 & 34 for ever and ever amen

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...