Jump to content
SAU Community

Recommended Posts

Power steering cut off while i was driving today. Took a tonne of muscle to move the steering wheel but it came back on after i straightened the wheel out. Also my RPM fluctuates up and down whilst idling. These issues don't always occur, it is really random.

Please help. Kind regards, Simon.

Also the RPM's dip low enough for the engine to cut off.

Edited by EarthShore

Obviously you know this is serious from having an accident point of view. brakes and steering affected.

By the time you feel it your engine has alsmost if not already stalled.

Normally I found when it happend to me to occur on corners. Seriously scary !!

Very rare when traveling in a straight line but occasionally had to keep the revs up at the lights.

I was thinking lack of fuel at one stage as it was normaly at qtr of a tank or less or round corners.

I didn't get to the bottom of it before significant work was undertaken on my GTR.

No Unfortuantely. I did a big end bearing.

Therefore had an engine rebuild. Whilst it was being rebuilt I had a lot of additioanl work done.

Personally I'd start by checking the flow of your fuel pump.

Could be time to replace fuel pump and repalce your fuel filter.

Hopefully someone like Jez and others can jump in on this thread.

I had the same issue whilst drifting. Car would cut out on entries and all the lights would come on dash for split second then it would come back to me.

Caused a lot if straightening and frustrating. Wouldnt as such surge/splutter and carry on. More just cut out and turn back on within a second or so.

Even did it with full tank. Changed fuel pump still no different, checked earths all seemed fine. Never got to the bottom of it.

my power steering becomes heavy after about 5 mins of driving, and im getting the rev drop when i stop, ive cleaned and resoldered afm, and changed the o2 sensor, ive also cleaned the aac valve which was black as the ace of spades! now im getting it but not as bad, ie its not stalling anymore! i think it could be a fuel pump earth issue, or the tps is not set correctly. ill be investigating this weekend.

It was the fix I least expected! But I think the gear box on the auto ha something todo with the peer steering fluid???????????? I'd check afm AAc and tps sensors and I suppose a gear box oil change couldn't hurt! I was genuinely shocked when I topped it up and 10 mins later the car was driving like new! Let us know how you get on tomorro mate!

Cleaned the AAC and checked the AFM but still didnt fix the idling issue. However I saw that the engines RPM could be manipulated by wiggling the bottom cord which connected to the TPS. I'm really starting to think it's the TPS. I ordered a new TPS and will fit it ASAP. I'll let you guys know how it goes. Cheers!

Make sure it's positioned right, I don't know how to do it but there is a thread on here about how to set your tps, even if you put a new one on but it's in the wrong position, it still wont work properly x

Thnx found it! Set the TPS to the correct voltage. It appears to have fixed the Idling problem, however it does idle too high now. I'm gonna have to do an idle reset tomorrow. Will let u know how it goes.

Also i lowered the idle using the screw on the AAC valve as much as I could. The idle still sits at a high 1200 rpm so I'm assuming I need to adjust the Idle using the idle screw on the ECU?

Edited by EarthShore
http://www.skylinesaustralia.com/forums/topic/404812-help-setting-tps-on-r33-s2/ if u have a S2 its the brown plug (bottom one) and the middle red wire :) cheers for the help. After setting the correct voltage to my new tps the car runs like a dream. As for the power steering problem it seems to have subsided for now :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...