Jump to content
SAU Community

Recommended Posts

Power steering cut off while i was driving today. Took a tonne of muscle to move the steering wheel but it came back on after i straightened the wheel out. Also my RPM fluctuates up and down whilst idling. These issues don't always occur, it is really random.

Please help. Kind regards, Simon.

Also the RPM's dip low enough for the engine to cut off.

Edited by EarthShore

Obviously you know this is serious from having an accident point of view. brakes and steering affected.

By the time you feel it your engine has alsmost if not already stalled.

Normally I found when it happend to me to occur on corners. Seriously scary !!

Very rare when traveling in a straight line but occasionally had to keep the revs up at the lights.

I was thinking lack of fuel at one stage as it was normaly at qtr of a tank or less or round corners.

I didn't get to the bottom of it before significant work was undertaken on my GTR.

No Unfortuantely. I did a big end bearing.

Therefore had an engine rebuild. Whilst it was being rebuilt I had a lot of additioanl work done.

Personally I'd start by checking the flow of your fuel pump.

Could be time to replace fuel pump and repalce your fuel filter.

Hopefully someone like Jez and others can jump in on this thread.

I had the same issue whilst drifting. Car would cut out on entries and all the lights would come on dash for split second then it would come back to me.

Caused a lot if straightening and frustrating. Wouldnt as such surge/splutter and carry on. More just cut out and turn back on within a second or so.

Even did it with full tank. Changed fuel pump still no different, checked earths all seemed fine. Never got to the bottom of it.

my power steering becomes heavy after about 5 mins of driving, and im getting the rev drop when i stop, ive cleaned and resoldered afm, and changed the o2 sensor, ive also cleaned the aac valve which was black as the ace of spades! now im getting it but not as bad, ie its not stalling anymore! i think it could be a fuel pump earth issue, or the tps is not set correctly. ill be investigating this weekend.

It was the fix I least expected! But I think the gear box on the auto ha something todo with the peer steering fluid???????????? I'd check afm AAc and tps sensors and I suppose a gear box oil change couldn't hurt! I was genuinely shocked when I topped it up and 10 mins later the car was driving like new! Let us know how you get on tomorro mate!

Cleaned the AAC and checked the AFM but still didnt fix the idling issue. However I saw that the engines RPM could be manipulated by wiggling the bottom cord which connected to the TPS. I'm really starting to think it's the TPS. I ordered a new TPS and will fit it ASAP. I'll let you guys know how it goes. Cheers!

Make sure it's positioned right, I don't know how to do it but there is a thread on here about how to set your tps, even if you put a new one on but it's in the wrong position, it still wont work properly x

Thnx found it! Set the TPS to the correct voltage. It appears to have fixed the Idling problem, however it does idle too high now. I'm gonna have to do an idle reset tomorrow. Will let u know how it goes.

Also i lowered the idle using the screw on the AAC valve as much as I could. The idle still sits at a high 1200 rpm so I'm assuming I need to adjust the Idle using the idle screw on the ECU?

Edited by EarthShore
http://www.skylinesaustralia.com/forums/topic/404812-help-setting-tps-on-r33-s2/ if u have a S2 its the brown plug (bottom one) and the middle red wire :) cheers for the help. After setting the correct voltage to my new tps the car runs like a dream. As for the power steering problem it seems to have subsided for now :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...