Jump to content
SAU Community

Sth East Subs - Fri 20/7 Or Sat 21/7 Cruise / Meet & Greet? Anyone Intersted?


Recommended Posts

Hi everyone... :action-smiley-069:

Just wondering if anyone is interested in a Meet/Greet/Cruise this weekend sometime

Depending on interest for this I was going to see if we could work out a place to meet & greet

then have a cruise?

Starting maybe somewhere along Princess Hwy ? Suburbs could be Narre Warren / Pakenham / Cranbourne / Berwick / Dandenong / or even closer in towards the city? Day / Night, doesn't matter. Somewhere for us all to park would be ideal ofcourse :)

Unless there is something already on I don't know about. Would be great to know if anyone's interested?

Anyone know if something like this takes place already? Esp for newbies like me? :blush:

If anyone interested or has any suggestions, that'd be really appreciated.

Cheers :rolleyes:

SKYG1RL

  • Replies 80
  • Created
  • Last Reply

Top Posters In This Topic

I'm wondering if ive seen some of you guys around too. Yep, I've travelled Old Dande rd recently too :) happy to fit in with everyone else here going by what's easier for the majority if you... Can always meet up more than once?

How does Sat night 8.30 (ish) in narre warren suit you all? Where is everyone from?? I'm happy to travel .. Thank u all for the feedback. Looking fed to meeting u :)

Blah blah I'm happy to leave to u to org in S/E subs? Sounds like you've done it before :)

Thread is now up:

http://www.skylinesaustralia.com/forums/topic/405197-last-minute-cruise-sat-21-july-2012/

The two most popular meet up points are normally Monash Uni & Doncaster. You want to try and keep the meets in a sort of semi-central location for anyone travelling from the west/north.

I'll promote it on the SAU VIC facebook page to gain any interest.

Fanastic! Thank you blah blah. Monash Uni would be awesome but you're right..Central for everyone is great. Didn't know that. Hope other newbies like me can come too. :)

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...