Jump to content
SAU Community

Recommended Posts

Hey.. Just looking up coilovers, i'll probably go with the BC BR's for my R34 GTT but just wondering if anyone has heard anything about these Emotion coilovers - http://www.ebay.com.au/itm/EMOTION-SUSPENSION-COILOVER-DAMPER-KIT-F-R-NISSAN-SKYLINE-R34-GTT-1998-2001-/120940699640?pt=AU_Car_Parts_Accessories&hash=item1c28a09ff8#ht_1310wt_922

Cheaper by $125 so i know i'd be best to go with the tried n true BC's but just thought i'd ask.... Mainly want coilovers to lower my car a few inches and also stiffen the suspension up for street use and the occasional track day. Cheers.

I'd been searching coilovers as I've just stuffed my rear ones in the GTT, could get them rebuilt but I think I'll just go to the BCs... The link shows they are from a warehouse type place which means tech support or warranty if anything goes wrong is probably limited, also doesn't mention if they are able to be rebuilt etc..... I would suggest sticking with the tried and tested product ;)

BR mate..... A few that have them said they are worth the extra $150 up from the entry level...... They are only $1299 delivered from what i can find, unless you've seen any cheaper?

Hey Chris,

Email Street to Track, for the BC BR coilovers they are $1165 delivered which is cheaper than any i have found in Aus :D

[email protected] or www.streettotrack.com

Hope that helps you!

Yep, BR's mate. You'd be crazy to get the V1's for the sake of $100.

And that price that Matt found, that's crazy stuff!

Yep was about to order at $1299 and then did a last minute google which led me to a Scooby forum and then onto Pauls website! SCORE!

Well I put $500 down on a laybuy for a set today, once the missus gets her tax i'll pay the rest... She's buying them for for coz i'm a top bloke hahaha... got em for 1250 trade.

I love them

Did you have other coilovers in the car prior? For a comparison? I've been running Teins and I was told they are similar.....

Ive ran coilovers in other cars, the gtr was upgraded from good old stock vspec suspension. And ill tell you on half dampening stiffness, these BC BR's are more comfortable.

I was also in my mates 32 with teins and far out they were stiff as f**k

Ive ran coilovers in other cars, the gtr was upgraded from good old stock vspec suspension. And ill tell you on half dampening stiffness, these BC BR's are more comfortable.

I was also in my mates 32 with teins and far out they were stiff as f**k

Mine aren't too stiff, it's just the rears that shat themselves.... Really looking forward to these now.... Is there a recommended dampner setting? I read some are stiffer in the fronts?

Mine aren't too stiff, it's just the rears that shat themselves.... Really looking forward to these now.... Is there a recommended dampner setting? I read some are stiffer in the fronts?

You won't regret it man, the BC's have a really good range of dampner. On full soft they are really comfortable, bit stiffer than the old King springs that used to be on mine. On full hard they are rock solid, but not as hard as the Tein's wound all the way up.

I was told when setting mine up to have the dampner at the front a little bit harder, to compensate for the weight of the engine. So I usually have my fronts on about 22, rears on 15. I soften them up a bit when I go to the track.

How do you work out what spring height adjustments before you install them, or is it a matter or adjusting them in the car?

The way I did it was I had a basic idea of how much further I wanted to lower it when I installed them, then I set them to the same height as my old springs and then lowered them by how much I wanted. That was with everything out of the car. Then when I lowered it later I did it on the car. Takes about an hour or so to do on the car, so it's no big deal. Just getting all four corners the same can be a bit tedious.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...