Jump to content
SAU Community

Recommended Posts

Ok so a bunch of interior and stuff for sale in the for sale section..

http://www.skylinesdownunder.com/forums/showthread.php?p=601407#post601407

A few random photos from the last two weeks..

Started stripping the loom... mm spaghetti... removing all excess wiring for hicas, factory speaker amp, boot light, etc.

DSCF3346.jpg

DSCF3347.jpg

Bucket of wiring removed so far... plenty to go

DSCF3364.jpg

Finally out of the garage on its wheels..

DSCF3349.jpg

Dash and door cards out... looking rather bare and very loud with no exhaust + no interior!

DSCF3350.jpg

DSCF3351.jpg

Got a few moments in the garage today so thought I'd mock up my latest purchase.

Grabbed a spare front hub and mounted it in the vice

DSCF3421.jpg

This box had shown up earlier in the week

DSCF3422.jpg

Inside - caliper dogbones to allow me to use regular calipers with 324mm rotors :D

DSCF3423.jpg

They come with all the hardware - high tensile hex head bolts

DSCF3424.jpg

Also these showed up - new 324mm rotors as used on R33 GTRs with brembos..

DSCF3426.jpg

DSCF3427.jpg

Now to fit one of my refurbished calipers and bask in cheap big brake goodness..

DSCF3428.jpg

@#$%^%E#@!! that doesn't look right.

DSCF3430.jpg

A rather large gap and only 3/4 of the pad is in contact... I got these calipers 8 years ago with the rolling body and had measured them then compared to other peoples measurements and decided they were S14 (280mm disc) calipers. Turns out I was wrong. :splat:

So to double check I grabbed the new 280mm discs I had and checked again...

DSCF3432.jpg

DSCF3434.jpg

Same gap...:headbutt: so looks like I'll have to sell / swap my calipers for a set of R32 or S14 ones... any takers?!

That's all that was achieved, I then headed for the beer fridge... :boohoo:

what an awsome build thread

Thanks mate' date=' been a bit slow as I sent if off for the cage...

But now things will start to progress again - picked it up yesterday from Frost Motorsport, just waiting on homologation before I can lay any primer down on it...

A few quick pics off the phone

[img']http://img.photobucket.com/albums/v90/samos69/Skyline%20Project/20120916_154016.jpg[/img]

20120916_154021.jpg

20120916_154043.jpg

Ok, got a quick hour in tonight, camera was flat so only got a couple of pics..

17x9 35p rim with 245 semi slick and a 20mm spacer

Hmmm, needs a bit of work. Broke out the guard flaring tool I bought a while back and gave the guard a bit of a massage.

Note: when trying this it makes life way easier if you disconnect the swaybar so you can jack up the lower arm to simulate the car sitting on it's wheels.

DSCF3475.jpg

Round 2

DSCF3476.jpg

Not quite enough, lets give it a bit more

DSCF3477.jpg

Almost, one more time and switch to a 15mm spacer (inner guard was going to foul and would have needed way more work)

DSCF3478.jpg

Sweet, plenty of room now :D

Had a look over the rims and realised the tyre guys have put them on all wrong, 2 are the wrong way around so will have to go pay for them to be changed as they were fitted up in Taranaki where I bought them... :mad:

And lastly a few extra pics of the cage from the other side:

DSCF3474.jpg

DSCF3473.jpg

Thursday I should be able to tackle the other side, then can lay some primer on the guard lips (I gave them a blast with the flap disk previously to check for rust).

And that's where it sits currently. I've located some R32 calipers so once I've done the other guard and given it a lick of paint I'll move onto the front of the car and finish the loom.

Still got plenty to do, and plenty of parts to be installed. The focus is on handling and stopping for the moment, the power upgrades are coming a bit later. Hoping to hit a test day in november to bed in the brakes and get some seat time.

Thanks for reading, comments / opinions welcome!

awesome build thread, this makes me more motivated on work on mine!! Keep it up :cheers:

Thanks! My motivation died for a bit but now the cage is in I'm raring to go. I literally have a garage full of parts to install, need to crack on.

  • 3 weeks later...

Had a quick hour tonight so got the car up on stands and removed the front wheels in preparation of brakes / suspension, etc.

Flying skyline:

DSCF3486.jpg

Flared the passenger side but didn't get time to disconnect the swaybar to test fitment

DSCF3487.jpg

Also had a steering wheel quick release show up from BLPP. Seems pretty well made, though the supplied screws are a bit soft :)

DSCF3480.jpg

Old:

DSCF3479.jpg

Part fitted

DSCF3481.jpg

Steering wheel component

DSCF3482.jpg

Join

DSCF3484.jpg

New momo race wheel. You remove the wheel by pushing the silver button in and twisting the housing through about 30 degrees.

DSCF3485.jpg

It's off centre as the momo holes don't line up, if I had a wheel that fitted the alterative hole spacing it would be straight so I need to pull it all off and move the boss kit on the spline to centre the wheel, but by that time I was needed to bath + bed the little one..

Stay tuned, another vehicle is joining the fleet this week :D

Oh look, another skyline :D

20121018_193455.jpg

Kids these days... sparkly purple bonnet :yucky:

20121018_193506.jpg

It's a (factory manual turbo) rolling shell that I'll be transferring all the parts coming off the race one as it develops to make a nice road car out of... It's currently set up to run an SR but I'll revert that back to RB goodness.

Probably a 12 month project at this stage, still way too much to do on the green one and not enough time.

I managed to wrangle the morning to spend working on the car today, didn;t get as much done as I'd like but any progress is good at this point :)

Pulled out my new R32 brakes which will work with the adaptors shown previously. Gave them a blast of brake cleaner to get the grime off and checked out the pads. They have no markings on them but the blue seems pretty distinctive... anyone have any ideas on what they are? The brakes were removed from a GTS-T in japan... They don't look like ebc bluestuff due to the 2 circles on the back (pics online show 4 circles and 2 v grooves on the face). I'm thinking they might be pagid blues? Either way I'll give them a run on a test day as they have heaps of meat left.

DSCF3490.jpg

DSCF3491.jpg

Next up was the exhaust, first to remove the factory cast dump. 4 13mm bolts up top, 2 13mm nuts down below (need a spanner for these) and it was off.

DSCF3493.jpg

The gasket looked to be in great condition which is a bummer as I had bought a new one thinking I'd need to replace it... $30 for a small piece of metal! Will hold on to the new one as a spare.

DSCF3495.jpg

New bellmouth dump next to the factory one - you can see how restrictive the factory one is compared especially where the internal wastegate wants to flow.

DSCF3494.jpg

Bolting it up make sure you do the nuts first! I had to undo everything as one of the bottom nuts can only go on with the dump pipe not fully seated due to a very tight clearance.

(no pic for some reason!)

Next up is the de-cat pipe. I had one made up years ago when I fitted my exhaust, 2.5 inch it was fine for then, but now I will be chasing more power so a 3 inch one was procured.

DSCF3496.jpg

Bit of wrestling and everything lined up, I really like the snub nosed look of this exhaust. :D

DSCF3497.jpg

DSCF3498.jpg

Onto the front - time for a clearance check, bit tight...

DSCF3501.jpg

So started pulling everything apart as I have lots of goodies to go in. Got to separating the LCA balljoint and smacked my knuckles with the crowbar.

Remembered why I hate this part so much and how every time I had to do it I swore I'd go and buy a balljoint separator so packed up as it was time to go look at kitchens with the mrs... and managed to stop in at Repco and grab hopefully the correct tool. With some luck work will continue tomorrow evening.

DSCF3502.jpg

Thanks for reading.

Hey man, looking good! Remember ages ago i said about the green 32 like yours.... I took a pic to show you -

HCj6nl.jpg

We were using it as an anchor lol, but a fluke about the paint etc :)

When separating the LCA ball joint, try bashing the side of the knuckle with a heavy hammer. Keep the bolt on top on in case you miss and damage the thread. Just need to dislodge the tapered part of the ball joint and it will fall out. Much easier than using a crow bar ;)

Hah crazy, I have a 32GTR bumper in the shed I haven't fitted yet but otherwise that's pretty close!

Yeah its what i thought when i saw yours.... He had only done the paint a few weeks before i saw this thread.... Bonnet came up on the FWY though hence the black bonnet now :laugh:

When separating the LCA ball joint, try bashing the side of the knuckle with a heavy hammer. Keep the bolt on top on in case you miss and damage the thread. Just need to dislodge the tapered part of the ball joint and it will fall out. Much easier than using a crow bar ;)

Yeah I was wailing on it with a hammer at the same time... they never seem to just pop out for me I always just end up injuring myself :wacko:

Will see how this separator goes, they had sold out of the fork type so I got one like this:

kdt-3916.gif

Yeah its what i thought when i saw yours.... He had only done the paint a few weeks before i saw this thread.... Bonnet came up on the FWY though hence the black bonnet now :laugh:

Bugger, I've had that happen on my old capri.... not fun times! Mine is black with black roof as that was the standard colour scheme craze back when I was drifting it early 2000s (plus I quite like it)

I've got a vented fibreglass bonnet to go on but thats not a priority as yet

Yeah I was wailing on it with a hammer at the same time... they never seem to just pop out for me I always just end up injuring myself :wacko:

Will see how this separator goes, they had sold out of the fork type so I got one like this:

Yeah maybe I've just been lucky but they've always popped about with a bit of convincing. It is easier when the cars up on a hoist rather than on stands though. Puller is always going to be a better option though, good luck with it

  • 3 weeks later...

Managed to get into the garage today and spend a couple of hours first tidying the place up then working on the front of the car.

With the new tool easily popped the balljoints. I managed to obation a set of R33 LCAs for nothing so will be putting them in as they have much better condition balljoints. They are also about 10mm longer, there seems to be some debate as to if this is beneficial, you get a bit more track but some people who know about these things seem to think it will give increased bumpsteer.

Either way I'll give them a go, here's a pic for comparison

DSCF3503.jpg

Also have some adjustable castor rods to go in as well

DSCF3504.jpg

Decided to drop the swaybar while the LCAs are out. Have this adjustable item to replace it

DSCF3505.jpg

DSCF3506.jpg

And to top it off some new end links as well

DSCF3507.jpg

You are supposed to reuse your D brackets with the whiteline bushes... not a great fit.

DSCF3508.jpg

After bending it out I run into this problem again, same as I did on the back.

DSCF3510.jpg

So a bit of thinking and the jack came into play..

DSCF3511.jpg

The problem now is I have this cranked up as tight as it will go, I may have actually stripped the bolt side and its not quite done up all the way. This is because the new bush is just too big. Does anyone know if there are bigger D brackets available or if I can leave it as is? Its super tight and the bar will rotate as it should...

DSCF3513.jpg

That was all as I gave up after the swaybar pissed me off.

  • 2 weeks later...

Should be ok but if your worries grab some washers and a slightly longer bolt and replace that original bolt, put the washers in that gap between body and D bracket. See how you go :) Nice thread building a 32 myself. Love the colour to :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for all the replies fellas. Gonna finish putting it back together and see how it handles the set up. If it starts pinging it’ll be parked.
    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
×
×
  • Create New...