Jump to content
SAU Community

Recommended Posts

So I'm new here, and I can imagine its been covered before on this forum. But I can't find a straight forward answer.

The rear suspension in my R34 25GT has gone, and I can easily replace it for roughly $600, but I wanted to put adjustable coil overs in eventually any way, so that is what I'll be doing.

I was going to put Pedders Sports Ryder eXtreme XA Coil Over Suspension into it, But the bloke at Pedders seems to think they will fit onto the rears no problems, but might not fit onto the front for some reason.

Also he is doing a really crap job at getting back to me with an answer, which is why I'm asking here.

Now, I can buy a full set of these for $1520, what I want to know is, will these fit onto my car? (year is 1999 in case that makes a difference) Or is there a better product I can put on there in the same price range? (Can't spend anymore than $1600)

I know I can put on normal suspension for cheaper and it might be better quality, but I'll be putting on a body kit and new rims in less then a year (hopefully) and I don't want to have to change the springs again when this happens, which is a good reason why I want them to be adjustable.

Any help would be appreciated, Thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/407838-r34-coil-over/
Share on other sites

Rears come in 2 sorts. Eye or fork lower mounts. Fronts are the same for all R33's & R34's regardless of variant. Tbh I would be going somewhere else and probably getting something a bit better than pedders. Entry level teins, Silk roads etc.

Link to comment
https://www.sau.com.au/forums/topic/407838-r34-coil-over/#findComment-6503885
Share on other sites

Apparently I must have eye lower mounts, I'm not using my car for any sort of drift/racing so they don't have to be the best,

How much would it cost for tiens or silk roads? And are they adjustable coil overs?

I don't know much about cars in general so sorry if I sound like an idiot haha

Link to comment
https://www.sau.com.au/forums/topic/407838-r34-coil-over/#findComment-6503905
Share on other sites

Okay, so I've looked over a couple of other forums posts, and I've narrowed down my search for my price range.

These are what I've come up with

http://www.pedders.com.au/products/52

http://www.isc-coilovers.com/coilovers.html

http://justjap.com/store/product.php?productid=18623&cat=422&page=9

http://justjap.com/store/product.php?productid=20209&cat=422&page=9

The last two are the same product I'm pretty sure. Its just that one is a fork type and the other is an eyelet type. I think the 1999 25GT has an eyelet type (If someone could clarify on that it would be great)

Could someone please tell me which of these would be the better one to buy? As I really want my car back on the road ASAP!

Thanks :)

Link to comment
https://www.sau.com.au/forums/topic/407838-r34-coil-over/#findComment-6503962
Share on other sites

I just had a quick look at the bottom of the suspension on my car, they have the eyelet connection on both front and back.. Which doesnt look like whats in the picture of this

http://justjap.com/s...&cat=422&page=9

Edited by MaccaD2191
Link to comment
https://www.sau.com.au/forums/topic/407838-r34-coil-over/#findComment-6503979
Share on other sites

I put bcs in my 33 the other week. Seems to be going ok at the moment.

Get them from street to track. They'll be about $150 cheaper than justjap.

Exactly what i did :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/407838-r34-coil-over/#findComment-6504621
Share on other sites

I've got Tein SS on my 34 now, the rears got noisy and collapsed, this is why i am trying the BC's :)

Why don't you get Fulcrum Suspensions in Queensland to rebuild them? TEINs are much better than BCs ;)

Link to comment
https://www.sau.com.au/forums/topic/407838-r34-coil-over/#findComment-6505245
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...