Jump to content
SAU Community

Would You Lose Sleep Over This?

Akshunhiro

By Akshunhiro,
in General Automotive Discussion

 Share

Recommended Posts

xntrq Veteran

xntrq

Posted
Posted

I'm no mech but I'd get it replaced.

From what I can see, there seems to be a hairline crack from somewhat in the middle of the crack where the chip is, leading towards the right side. As you drive, the roads, speed bumps, holes etc. anything that will cause vibration will cause the crack to grow and eventually break off. Given that it pulls the belts, you can imagine what would happen if something hit it and bent it out of line. Could shave off your belts or worse case scenario, the piece breaks off completely, gets flicked up into the belts, causing more damage to other parts.

This is from my point of view, a crack like that, I'd get it replaced when I can. Fork out some money to replace this than forking out 4 times more replacing other bits that this has caused.

Just my 2c.

I may be completely wrong though.

GTR-N1 Grand Master

GTR-N1

Posted
Posted

That's the term I was looking for. Couldn't put my finger on it so it came out in 100+ words.

No worries Ricky :) - you were quite explicit.

I'm used to my wife coming out with a 20 page thesis hehe...

Hot33r8723 Rising Star

Hot33r8723

Posted
Posted (edited)

Nah mate I wouldn't bother that's not gonna do anything when the crank shaft is spinning there's enough vibration in I already a little chip like that won't do jack all I'm sorry i won't full stop and u know how I no cos I ran a balancer like that for years pulled out my crank and everything was fine and it was 20 times as worse condition Ull be fine mate take the advice it will be fine

Edited by Hot33r8723

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 persistent issues. P/steering and lag/misfire

      By GTSBoy · Posted

      Power steering is probably because someone has nuked the HICAS CU and you no longer have the variable power asist doing what it is supposed to. How much boost are you running? You are aware that any more than 10 psi on the stock ECU is just asking for it to go to full R&R (that's Rich & Retard, which is effectively Retarded and Retarded!) which kills all the power. Depending on the exact conditions, it can just be runnign on the fat and stupid end of the maps, then the conditions change, you make a little more boost and the ECU goes into panic.
    • Kapr
      Freddy Plenum vs Genuine options RB25

      By Kapr · Posted

      @BuiltNotBought Just as GTSboy said.   If you want driveabilty and more low down torque..keep the stock runners. They are VERY good from a factory. I have them too on my RB25DET NEO and as a GTSboy i have fmic but with stock piping route(i have Blitz intercooler) Iam making around 320 BHP and the car pulls "hard" from like 2,5k all the way to 7k. I have it dyno tuned to mimic N/A power curve and making little less max torque due to the smallbox tranny. But driveability is very great. I had 350Nm below 3k so car feels very quick.
    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      Looking to sort out a couple of issues on my skyline  It recently was rebuilt, however rebuilder long story short did not give two flying effs about the work he did. So moving forward it's running but I have two persistent issues 1) it has a misfire / lag type of issue (was at higher RPMs but I had a dead piggy back ecu removed which improved it) now it's not as bad but still does it at random, I thought it may have been a boost issue I'm running an older turbosmart dual stage controller, turbosmart told me to try running off gate pressure however it still has a lag at random times. It has New MAF, maf plug, coil packs, sparks, CP harness.. injectors tested and cleaned. Factory ECU. 2) Power steering issue. It is tight as anything. Flushed power steering, rebuilt my pump because the bearing was shot. Flushed again still tight (mainly when parking and going slow into my driveway etc)  No kinks in hard lines, replaced the lines I could see had cracks. Still tough to steer.  I was told to shim a coin and place into the solenoid plug? Is there anything else. My steering angle sensor also has a issue. It's a used one I replaced, does it need to be calibrated? I feel like I've tried everything and this car is my voodoo doll.   
    • Dose Pipe Sutututu
      Neil's R33 Gts-t Build

      By Dose Pipe Sutututu · Posted

      Holy shit... wow!!! I totally missed this
    • MBS206
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By MBS206 · Posted

      One main filter. Each tank has a prefilter to keep rocks and small children out, then the big main filter that also does water separation. Clogged the first one so bad it was like a rev limiter at 3200rpm. Literally just like dropping the throttle off and maintaining rpm!
×
×
  • Create New...