Jump to content
SAU Community

Recommended Posts

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Yeah Bob & wolverine, I imagine the RB30 should provide the torque the stag needs; will post dyno sheets & all, but im yet to drive it or start it for that matter! Still got some work to do, like manual conversion & rear manual subframe from GTR, plus finish brake conversion & then tune! But, im expecting over 350awkw & a truck load of torque, so im sure that will get it off its fat arse!

My s1 has elec mirrors, I assumed they all did?! As for what to look out for, well like any car, things age & wear. If its had an easy life & kept well maintained, it should run happy for years. But things occasionally do go wrong & such is cars! If its done over 100k then check if it had its major service & timing belt done. No turbo noise. Good compression. Good cooling system. etc... Service history? Then should be ok!?

Rust under the mirrors is common. Broken or missing door weather strips (expensive & somewhat difficult to get). The mechanicals are very much the same as the R33 GTR & motor is R33 GTST (s1) or R34 GTT (s2) or R33 GTR (260RS)! Read all the threads, it will give you a pretty good idea of whats going on with Stageas & what people want or have problems with, lots of info in the stickies too!

These cars are pretty tough to a point, so if left std & driven normally, then you shouldnt have any real issues! If you chose to mod &/or drive "spirited", then you have "swallowed the red pill" (time to get your hands dirty & your wallet cleaned)!

Buy one, they're awesome!

Is the only reason not to pick an 260 due to the price what are the engines like and performance upgrades are they easy as on the other motors like say if they were they same price to buy and u put the same money or mods on which would end up a better car performance and drivability and life of the car

The Autech 260RS is the better car, though very similar to the RS4S in most areas. The 260RS is an R33 GTR mechanically! The RS4S uses the R34 GTT engine & has standard s2 Stagea brakes (smaller than the 260RS Brembos), different body kit, along with a few other minor changes! But the RS4S is roughly half the price over here! So with the money saved, you could make the RS4S better for less, if you want to mod it! But if money is no issue or you dont want to mess with it too much, then the 260RS is the best Stagea in the range (besides the elusive Nismo Stagea, which is mechanically the same as the Autech 260RS anyway)!

Performance = 260RS

Value = RS4S

If your going nuts on building a monster, then might as well use a S1!

Basically, If I won Lotto or something I would hunt down & buy the Nismo 260RS, just to have it on the compliance plate, but seeing as I have a S1 RS4V already, I would just finish building that, as it wouldnt matter which car I started with, they'd both end up the same!

They all have a very similar drivability, all offer similar performance once modified, life of the car is the same!

Just work out your budget or other confining factors, what you want/need to do with the car; then decide on which best suits your needs & wants! (There isnt a bad Stagea, they are all awesome, thats why we own them!)

Zorro has the right of it.

If you are budget conscious then it's hard to go past an S2 RS4S (or S1 for that matter). It's 85% of the 260rs for half the price. To make it 120% of the RS will still cost less than an RS. But then, at the end of the day, it's not an RS.

If you specifically want an RS because it's an RS then go for it, I doubt you'll be disappointed. Just bear in mind there is a cheaper way to get into a stag or cheaper a way to get into a faster stag by starting with an RS4S.

Auto's only

1 for snow (2 gear takeoff i think, maybe also 50/50 torque split)

power is auto too (earlier kickdown)

auto's also have the awd button (locks 50/50 up to like 40kmh or something like that)

Manuals get none of this

Are there any problems with any models as you put the kms on these cars want to what the life of them are like

The stageas are built well mate. Mines just passing 210,000kms with nothing but regular servicing. Including alot of hard driving and even a few track days. Except for a clutch which is the result of abuse with the front shaft out :D

Do they have a speed limiter at 180km is it possible to override or remove this

Do the rs4s all have the neo engine ?

I honestly believe ALL your questions and queries will be answered by inspecting a few C34's and M35's, test driving both.

Otherwise this thread will drag on forever without a final conclusion and you'll still be none the wiser.

Do they have a speed limiter at 180km is it possible to override or remove this Do the rs4s all have the neo engine ?

yes and yes

all s2 c34's have neo's

and the manuals only came out as s2's (apart from the 260rs's)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...