Jump to content
SAU Community

R34 25Gt-T Badge?

Lwood

By Lwood,
in Exterior & Interior Styling

 Share

Recommended Posts

Lwood Collaborator

Lwood

Posted
Posted

The badge that sits just under the right set of rear lights on most 34's. Where can you get these from? I have looked all over the forums. One suggestion was to contact Nissan directly. After sending many emails to Nissan and going into my local Nissan shop. I was informed that they are no longer available.

Has anyone had any luck procuring these? Or knows where they are available to purchase?

Link to comment
https://www.sau.com.au/forums/topic/409599-r34-25gt-t-badge/
Share on other sites
gtsttrk Mentor

gtsttrk

Posted
Posted

Have you tried eBay? Just Jap have a lot of badges so I'm sure you could find one there. Or of you're desperate contact Jesse Streeter or import monster. Even try the wreckers. I would have though that these would still be quite easy to source.

Lwood Collaborator

Lwood

Posted
  • Author
Posted

Have tried Just Jap, have pretty much every badge but the one I am after. Ebay is full of of GTR badges however, I did find the one 25GT-T badge but it was in the UK and they would not ship to Australia. I'll contact Import monster and see what he can do.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...