Jump to content
SAU Community

Recommended Posts

Location: Newcastle Nsw but can freight anywhere in Australia

Item : Rb25det Engine

Complete Rb25det with all sensors, turbo, manual ecu and harness etc so if theres anything not listed just ask

Comp tested all within 3 psi of each other but a big of a noise in top end. Stickly lifter maybe engine blew no smoke and ran perfect other then noise

Stripping down to long engine but can disassemble more if required

Intercooler piping set $120

Gfb Deceptor Bov ( no in cabin switch only loom) $260

Drift air filter with adaptor $40

Airflow meter $100

Manual Ecu $120

Engine Harness $165

Injectors and rail $160

Stock turbo with dump and shields $275

Stock Manifold $60

Stock air intake pipe $50

ac compressor $100

Alternator $100

Starter motor $100

Coilpacks $25 each

Coilpack cover $75

Throttle body $60

Tps $45

Plenium stock $75

Drive belts $10 each

Long engine $850

Anything else just ask

Having dramas loading a pic ill load one via photobucket tomorrow.

0402555849

Link to comment
https://www.sau.com.au/forums/topic/409687-parting-out-rb25det-series-2-engine/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...