Jump to content
SAU Community

Error 21 Ignition Signal Problem

GiJOr33

By GiJOr33,
in Engines & Forced Induction

 Share

Recommended Posts

GiJOr33 Experienced

GiJOr33

Posted
Posted

The diagnostic computer is giving the above error on my R33 GTSt. Anyone have any idea what i should check to see if it's the problem?

Basically the symptoms are very rich, very rough running. It missfires heaps and struggles to idle. The plugs foul to the point where they are black and wet.

It happened after i took it in for a check up on the dyno so i'm not sure if it's something that just happened to fail or if it's something they have done. I took it back to them and they changed back what they did to the way it was (not much changed).

My car has a HKS FCON V, HKS VPC, and a HKS PFC-FCON.

It's got me buggered. I've tried another Crank Angle Sensor, i've put new spark plugs in. Could it be coil packs, or possible the PTU (the little thing that sits up the back of the engine that plugs into the coil pack loom).

Any tips would be good.

Link to comment
https://www.sau.com.au/forums/topic/41002-error-21-ignition-signal-problem/
Share on other sites
browny Proficient

browny

Posted
Posted

AFAIK the computer diagnostics only pick up short/open circuits or out of range signals. When the ECU detects an error in any of the systems it checks it enters a "safe" mode where the engine is only allowed to run with very conservative settings (ie rich, retarded timing, rev limited). The actual settings vary depending on the failure detected.

So the most obvious thing to look for is something that has been accidentaly left unplugged, which you have probably already done.

Next you need to start investigating individual components and their wiring. It could be something as simple as an earth that has been left off or a wire in the loom that has been broken somehow. It also could be something that has failed. Try playing swapsies with known good parts.

A multimeter and an engine manual are your friend.

GiJOr33 Experienced

GiJOr33

Posted
  • Author
Posted

yeah... i don't have an engine manual or a manual for the HKS computers. Oh well... i'm tipping that something has come loose under the foot well where the FCON V is sitting. The car ran perfectly fine before i dropped it off for a tune up. I've looked at all the things in the engine bay to make sure they are all plugged in correctly, such as the igniter, the coils, the CAS. We changed over the CAS to see if that was the problem, it wasn't. I've got a spare set of coil packs and an igniter here that i can check. All the injector plugs are on etc so the only logical thing to check is the dogs breakfast of wiring looms under the passenger dash/footwell

GiJOr33 Experienced

GiJOr33

Posted
  • Author
Posted

yeah i've pulled the battery out (flat from trying to start it on fouled plugs), so it will have the night to reset, tomorrow i'll try and start it again with clean plugs and a different Ignition Amplifier as well. Hopefully all will be ok.

GiJOr33 Experienced

GiJOr33

Posted
  • Author
Posted

well i started it an still no good. The guy who buggered it up had a Snap-On box that plugged into the port under the steering wheel. That's where i got the Error 21 from. I have a funny feeling that he's wiped the HKS computer of the tune that was in it so it's back to factory defaults.

GiJOr33 Experienced

GiJOr33

Posted
  • Author
Posted

Well i have changed everything except for the HKS computer. I've changed crank angle sensor, coil pack igniter module, i've tested all the coil packs (all 0.8 ohms), i've swapped over the factory computer with another one. So all that is left in the ignition circuit is the HKS FCON V, HKS VPC, and PFC-FCON and also the wiring loom. So either the HKS computer has crapped itself (or he fried it), or the wiring loom is damaged.

Starting to piss me off. I wish i knew what this other tuning place had done to it...

Andrew

blind_elk Grand Master

blind_elk

Posted
Posted

Have you checked the power supply to the ignitor / coils? Or the relay for the coils?

Error 21 is raised when the ignition signal isn't generated. If it was a problem with CAS, it would be error 11.

blind_elk Grand Master

blind_elk

Posted
Posted

Power is supplied to the coilpak, and the ECU earths the coil thru the ignotor to generate spark. Work out which wire is the power at the coilpak - if you pull the plug off and look into the plug, I think it will be the left-hand of the three pins in the plug.

Switch ignition to IGN / ON (not START), then measure voltage to earth (chassis / engine). It should be basically 12V.

If it's not 12V, I really have no idea WHERE the relay is located - it will be up to you to go exploring.

GiJOr33 Experienced

GiJOr33

Posted
  • Author
Posted

well after spending the whole day on it the mechanic found a few problems and in the end got it running. I'll post up what the problems were when i pick up the car and have a chat to him about it. I think it's going to cost me a hell of a lot though, so i'm not looking forward to the bill!!! And there is a bit more to do tomorrow, chuck it on the dyno and check the fuel ratios etc and just give it an all over check up to make sure everything is in check. At least my HKS computer isn't fried and the motor isn't blown!

so thanks to everyone that gave suggestions on what to check. I tell ya, this whole engine transplant saga has meant i know the RB25 almost backwards now and would be confident to do it again. Just a shame the couple of places i took it to to do the things i couldn't (check A/F ratios and pull out the old motor and drop in the new) did a pretty half assed job job. Oh well... disappointing but i spose once you find a good mechanic you need to stick with them!

Andrew

GiJOr33 Experienced

GiJOr33

Posted
  • Author
Posted

Yes... the car is all working!!! cost me $670 though... had some cracked wires to the computer. The igniter wasn't grounding properly, the vacuum hose to a map sensor was stuffed... so a few hours spent sorting it out but it's all fixed. Chucked it on the dyno and set the max boost, gave it a quick tune to make sure everything is in check and pulled a nice 222kw at the wheels at 0.68bar (9.8psi)... so i'm pretty happy. All i need to do now is bigger pump and i should be able to get it up to 1.1-1.2bar and have some good power!

Andy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • wizlb
      Flex Fuel Kit Workshop

      By wizlb · Posted

      Thanks Dose.....    I appreciate it!!
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • Piggaz
      Ogura orc1000f vs Osg tr2cd vs Osg r3c experiences, max torque/max hp?

      By Piggaz · Posted

      I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • uchoa
      Yet another RB Neo misfiring thread after reading all the others.

      By uchoa · Posted

      Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...