Jump to content
SAU Community

Recommended Posts

since last night I bad rattling noise as emerged from engine bay...Its definiately not the dash.

I find I can make the sound worse if, I put into gear (i.e. first gear) and release the clutch to the point of friction where it lets go, without putting pressure on the accelerator pedal..

ANy ideas? This is worrying me....

Link to comment
https://www.sau.com.au/forums/topic/41004-help-major-rattling-noise-on-s15/
Share on other sites

Na it will be ten VVT my friend. My S14a does it and nearly every S14 i know and some S15s that have a few more K's(not Many though) do it. Common problem. Cost around 1500 to fix, not really worth doing as it doesnt really cause any problem. If the car is still under warrenty get it fixed, he he.

its hard to varify what the noise is exactly without hearing the noise coz some noises sound quite similar, but u say u can make it worse when selecting a gear but the noise goes away when u engage the clutch abit in gear? Possibly an internal gearbox drama, mainshaft bearing/s, counter shaft bearing/s something like that, but again unless i know whats actually happening and when, with what noises etc its hard to tell u, ur best bet is to talk to someone in person(ie a mechanic or gearbox place) and see what they say. U could try talking to boosteds15 of www.boostcruising.com he has an s15 which has had afew gearboxes replaced. maybe u have the same drama

my s15 has done 28000kms. and it doesnt happen when i rev the car or while normal driving.

i agree sweetr33 sounds a gearbox problem....ICE in melb says its possibly the thrust bearing. Pain the in arse to change cos u gotta take out the whole gearbox....

I can make the noise appear by putting into 1st gear, then slowly disengage the clutch to the point of friction where I nearly stall. By the way this is when NOT pressing the throttle.

could it also be the engine/gearbox mount?

I know i might be repeating the people above but it really sounds like a thrust bearing issue had a similar problem on an import gemini, turned out the spring that holds the bearing had come off and lodged itself between the fork and bearing, thus always making it touch the pressure plate.

Mind you my problem ended with a screech squeel yelp and than bang as the pressure plate disintigrated the thrust bearing, in amongst other things.

Pull of the g/box and check it and its not that much of a bitch if you gotta pit/hoist.

there is 6 bolts holding the box on the bellhousing 4 holding the tail shaft 4 bolts mounting the box disconect the slave cyilinder and yank out the shifter.

Ohhhh and don't forget to drain the oil.

ooo and trhe starter motor 2 bolts holding that one

Hope it helps

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
    • I _think_ that one has a christmas tree or some other retainer spike into a hole in that panel under it. Come in under it with thin scredrivers and just pry it gently up. If you rip the ears off the retainer pin....so what? Just stick it back down after with a bit of race tape and carry on with life.
×
×
  • Create New...