Jump to content
SAU Community

Recommended Posts

hey guys

i was recommended the NGK BCP6ES spark plugs.

i rang a few auto stores and they only have NGK BCP6E which they rekon are the same plugs, but i was told to watch out to make sure its the NGK BCP6ES with the S on the end.

anyone (in perth?) know where i can get hold of them?

Link to comment
https://www.sau.com.au/forums/topic/41035-ngk-bcp6es/
Share on other sites

If i could tell you one thing it would be this. PLEASE buy the BCPR7E(S) and gap them to 0.8mm if they aren't already.

If you run more boost than stock (or intend to) you'll be much better off. They're the same thing as the plugs you mentioned but one heat range cooler. They are no more expensive.

Adrian

Link to comment
https://www.sau.com.au/forums/topic/41035-ngk-bcp6es/#findComment-842659
Share on other sites

Hey Adrian,

I found I was worse off with the 7 heat range. For a daily driver, they fouled a-lot quicker before I got my SAFC than the 6 heat range would. The standard heat range for an RB25 is 5, so 6 is one cooler. I would disagree with getting the 7's unless you got quite a few mods 200rwkw++, and stick with 6's for basic mods, and 5's if completely stock...

Link to comment
https://www.sau.com.au/forums/topic/41035-ngk-bcp6es/#findComment-843300
Share on other sites

guys, if you've ever tried calling NGK for a recommendation, they have actually told me to sell BKR6E plugs to skyline drivers if they want a cheaper copper core option to the more expensive Platinum and Iridium tip long-life plugs (only differerence is the greater resistance to fouling)

Reason behind the "K" instead of the "CP" is that the "CP" is a projected tip type plug and NGK have discovered that the "K" recessed type plug seems to complete combustion more effectively due to the shape of the cylinder head "squish zone"....

that will add more discussion to your thread (adding to the numerous hundreds of other spark plug threads on here) Oh, and yes totally agree with the gapping and heat range advice above. Buying NGK plugs without the "-11" should give you the default 0.8mm gap.

Link to comment
https://www.sau.com.au/forums/topic/41035-ngk-bcp6es/#findComment-844378
Share on other sites

  • 8 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Noice. Congrats on the big day too!   don’t forget to never eat in the Skyline 🤣
    • Overnight parts from Amazon, let's go. Replaced nearly every o-rings, minus 2x from the pumps. Seems the kit is short? Then again when I replaced the main pump a few years back it did come with new seals so we are good. Yiewwww, ready for legal stimulants.
    • I'm only really familiar with the R33 setup, the factory filter is very much an encourage fuel pick up thingo.  The factory pump sits about half way down into the tank and the sock runs down into the bottom of the tank.  Mounting an aftermarket pump in the factory location with the typical tiny Walbro filter, I had huge fuel surge issues once the fuel level dropped below 50%. 
    • Hi Gent, Got my r34 GTT 1999 ,wondering if anyone has a stock airbox with snorkel? currenly it has a pod filter which im planning to remove and install the stock part, as this needs to go to vic road for inspection. Appreciate your assistance. 
    • Yeah, I still dunno. The size of the sock should only matter if it is blocked. It is, after all, a filter rather than a "thing to encourage fuel pickup". He has modded the original so that it is now down on the floor, so it's not physically the same as in the original complaint, yet does the same thing. I therefore lean to the problem being somewhere else. Sticking some dynomat on there is a worthwhile experiment, but I'd put $10 on it not fixing the problem.
×
×
  • Create New...