Jump to content
SAU Community

Recommended Posts

Hi guys

Just needing some help before i go to the mechanics.

r32 gts4 RB20DET. Just recently I had the heater on full blast then i notice the smell of coolant burning up and car was over heating. Now when I pour water into the radiator it drip quiet fast out under the intake manifold. I thought it was the heater hoses. But ive stuck my hands under there and no water is coming out of the heater hoses.

Where could this be coming from?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/410792-coolant-dripping-out/
Share on other sites

Under the plenum there is a tiny hose maybe 2 inches at most mine was split there, can be a pita to change as access is poor.

i had a few of these splits in mine

http://imageshack.us...98523145304.jpg

Edited by 4DR_32

best bet is to take off the start motor as picture ^^.. and replace all those hoses with just generic ones.. I've had them let go before.. also there's another one that goes from the throttle bottle and down under the plenum.. that likes to explode too.

Yeh that was it, but i did it from above without removing anything jus had a torch and mirror the only hard bit was putting it back on.

Getting one end on is easy the other is a bit harder I sat it in boiling water for a while to make it softer and more forgiving to get it on. Replaced the clamps with worm drive ones too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • BRUH, one of the biggest mistakes of my life..... and i've had plenty ;[)
×
×
  • Create New...