Jump to content
SAU Community

Recommended Posts

Hey all,

This started happening yesterday morning, but was hard to diagnose due to lots of condensation (was a bit chilly yesterday morning). Basically what happened, is when i would drive off, then stop, smoke would come out. And when i accelerate then back off. Smoke would come out again. Doesn't look like it comes out while actually accelerating, only in between. (if that makes sense?)

After work, i got the old man to follow me around, he said only a small puff came out when i left my house then nothing but a bit of blackish/grey smoke under boost (normal i believe with a stock ECU). Did a few tests, light load - high/low revs, 4th under load up hill and WOT. small cloud of smoke under boost. Werid...

Anyway, while i was driving today i noticed quite a alarming rate of smoke coming from my exhaust, i pulled in and took this video.

https://dl.dropbox.c...1009_082732.mp4

It won't smoke when it is idling, but when accelerating it puffs out like crazy, the car was warm when the video was taking. It seems worse when the engine is cold. Looks like a bluey smoke, so im thinking oil??

Tips on how to diagnose whats wrong with my car appreciated!

Temps seem fine, Still goes the same (not that i gave it a hard time due to the smoke screen).

Hoping its turbo related because i am replacing them. I'm scared to drive on it, and you know have this lame thing called work, really don't want my engine to go BOOM

Edited by Booki
Link to comment
https://www.sau.com.au/forums/topic/411139-gtr-blowing-smoke-help-troubleshoot/
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Looks like condensation. Chilly morning = condensation, especially if you don't drive the car very much.

Take the car for a long drive and see if it still does it when the weather is warm (read - above 20deg c)

Looks like condensation. Chilly morning = condensation, especially if you don't drive the car very much.

Take the car for a long drive and see if it still does it when the weather is warm (read - above 20deg c)

I thought it was condensation too, But I dunno. It seemed a little "blue" and heavy for condensation.

I will take another vid when I move to my next job site.

Hado - I checked my coolant last night, looked normal green color. Will check it before i drive off again.

Ok, Started it up to go drop it at home.

No smoke...Revved it a little, no smoke. Wasn't even worth taking a video.

Even on the drive home, nothing came out.

Decided to play it safe, and drop the car off at home. Gave it a bit of a rev when i got in the garage and a small puff came out, but then nothing after wards.

Beats me... It was BAD this morning. Now, nothing. Regardless using the bike till i figure out wtf is going on.

and Hado - Coolant levels normal, still green.

Update: checked coolant. Its used some, although it is still clean of what i can see of it. Checked oil cap, and all looks good from that view, as well dipstick oil. Color looks normal. So i don't think its a head gasket (least im hoping not)

Stock turbos

Edited by Booki

white smoke on rb26 usually means turbo seals. have a look in the coolant reservoir tank. can you smell oil? incorrect anti-freeze ratio can also cause white puffs of smoke. do full coolant flush from block and see how it goes from there. my gtr does it on WOT. no biggie.

Starting to replace my turbo's, and noticed the rear one was seeping oil.

Intercooler also had some oil in it too.

So far have all the piping off, turbo heat sheilds off, undone the front pipe bolts to the dumps.

It's coming along alright so far, only because the old man is helping out (by helping out i mean doing 90% of it).

Hopefully we don't get stuck, the job itself doesn't seem hard. Its just all the variables (rusted nuts/bolts, tight space) that make it difficult.

Dam RB26

  • 3 weeks later...

Ok....Started up the GTR with BRAND NEW -7 turbo's, let it idle for a bit while i was putting in my fresh coolant (you know the drill) and the same shitty smoke was there.

No where near as bad as the video posted up, but still noticeable.

Idea's?

Hard to tell, Only started it twice.

Turbo's have only just been put on, have not driven car due to it not being tuned.

The smoke is hard to describe, it looks like condensation but right now its about 22 degrees? So i don't think its condensation.

Smoke comes out on de-acceleration.

Only revved it as high as 2500-3000rpm

I have a similar issue with a customers car. I tried a new pcv Valve to eliminate it from the diagnosis and the issue is still there.

As Dan has said, more than likely valve stem seals.

They are a pain to diagnose tho.

Have u done comp and leakdown test?

Havnt done compression or leak down tests yet. Will do some more trouble shooting when I finish up work for the day. Hoping its not a head gasket or rebuild time, only put 5000kms on it since ownership :(

Will try and get a video up, keep me posted on how you go with your customers car :)

Edited by Booki

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...