Jump to content
SAU Community

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Youtube Links.

Dropbox sucks for streaming.

I'm lost for idea's. Figured if it was a head gasket it would be constant smoke? Get worse with rpm's as pressure builds up? PCV valve cleaned, made 0 difference. Although it was gunked up and rattled when i shook it (think thats normal)

http://www.youtube.com/watch?v=UVU3XbimIsc

http://www.youtube.com/watch?v=G3aQ_biZaf0

Edited by Booki

Going to start taking it all apart tonight...just after i had put my sweet new -7's in :(

Anything else I should be changing while the head gasket is out?

Recommendation's on head gasket? (genuine, after market? Nismo? cometic?)

Edited by Booki

Just replace i with a standard gasket from Nissan. They aren't that expensive and are very good quality.

Get the cylinder head fully recoed while it's out. Valve regrind, stem seals, deck ect.

Get your injectors cleaned right before the head goes back on

Replace all the heater hoses

Still running stock injectors, worth spending the cash to get them cleaned?

Are there better options out their then the standard nissan gasket? While i would imagine they are good quality, I am planning on running 17-18psi boost on the -7's, would the standard gasket hold up? Or should i look at something after market?

Know any places that are reputable to get the head done? And rough costs involved?

Edited by Booki

Still running stock injectors, worth spending the cash to get them cleaned?

Are there better options out their then the standard nissan gasket? While i would imagine they are good quality, I am planning on running 17-18psi boost on the -7's, would the standard gasket hold up? Or should i look at something after market?

Know any places that are reputable to get the head done? And rough costs involved?

We use stock gaskets in applications over 600hp and 30psi boost without issues.

If you do the job correctly, it will be fine

Anybody got any tips for taking the head off?

Both turbos are back out.

Cam gears and belt still on, looks like my cam timing is one or two notches out on the exhaust side...

Do people remove the head with the plenum attached? It looks like a bitch to remove the brackets hiding underneath the plenum.

Honestly surprised myself in how quick I was able to remove the turbos

Edited by Booki

Well for all those following, Heads off.

IMG_20121104_160011.jpg

Now with the head out, I will send it off for a reco, though in the process their were some casualities. I ended up cracking it and just cutting a heater hose, and a two electrical connectors were damaged. Anybody know where to get a replacement heater hose and this particular electrical connector?

IMG_20121104_155908-1.jpg

IMG_20121104_155816.jpg

The other I am hoping to just open the connector, and solder/crimp it back down.

In the mean time I am hoping to get a neater engine bay setup, wanting to eliminate some hoses that are not required. Mostly the ones under the Plenum as they were a BITCH to get out!

Also, This wiring looks real dodgy and pox as, I don't think its standard/original wiring. Can anybody confirm? Then i will start following it up and eliminating it. Or at least making it neater.

IMG_20121104_160243.jpgIMG_20121104_160111.jpg

Edited by Booki

Top hose in the pic that is broken - get it from Nissan (Usually the first place you should try)

The plug should be the same as Bosch 2 pin standard so I would try Repco etc for those. Pretty common plug. It won;t look the same but should still fit the Bosch 2 pin knock sensor.

The other wiring is anyone's guess

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...