Jump to content
SAU Community

Recommended Posts

Has anyone on here used a ts2b clutch before?!? To suit push type 32 GTR-33 GTST?!?!

I have 3 carriers to go with the clutch. A 20mm, 12mm(haven't measured this one) and an 8mm!

We've put the clutch on and used the 20mm carrier but its compressing the diaphragm springs as the box is going back on!!

20mm carrier was what was listed to be used with this clutch!

Can anyone tell me what they've used or post up a picture or something. Maybe some accurate measurements!

Heres a picture of the 20mm and 8mm carriers

post-14265-0-90455500-1350781385_thumb.jpg

Edited by Turbz_13

Where are you taking the measurement from (20/8mm)?

The one on the left looks like the short one. You need to use that carrier but it looks like you have the wrong bearing on it. The OS Giken uses a small diameter throw out bearing. Not the standard one

hey mate,

sorry yeah the one on the left was the 8mm carrier and the right the 20mm carrier. and i have one that has come out of the car thats about 12mm, i didnt get the chance to measure it and it still at the car at the place we were working on it. ill get correct measurements when i get back to the car!!

taking the measurements from the release fork pad to the back of the bearing.

the one on the right, the 20mm carrier, is what i was told i needed to use with this clutch. the bearing on the 8mm carrier isnt what im using, i tool the clutch to a clutch place and got the correct bearing to suit the clutch.

i just edited an image for this purpose but. i measure my carrier like "A#" in the diagram, unless its a total sleeve length or measurement "B#" is where i need to get the 20mm from?!

post-14265-0-84112400-1350803593_thumb.jpg

Edited by Turbz_13

I do have a part number for the nissan carrier that os giken listed to use with the clutch, but i cant find any info at all or pictures of it

30501-K0401

Edited by Turbz_13

thanks mate! cheers for the help!

that's the one i originally got with the clutch but i made some calls to the australian "os giken" distributors JUST to be sure, who told me to get a 20mm carrier!

i have the bearing(isnt in the picture) i took the clutch to the clutch shop to get looked over and made sure it was still in good order and to get the correct bearing for it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did you pay with a credit card? I'd be putting a charge back through then finding a new sparky to sort it out. 
    • If you mean the alarm immobiliser; theyre internal to the alarm itself which makes that difficult; I couldnt even see where he put it; its not in the same place as last time; but with all black wiring it might be very challenging to trace  I had someone turn the key for me as I know it only primes for a couple of seconds As my post above; I am getting no voltage to the pump at all; but I am testing continuity of the power line (SB) from the pump plug to the relay fine. As well as the negative from the pump plug to a 12V constant.    Yeah; he blammed the no start on a bad battery; said I needed to get a new battery and it'll start. Turns out the battery drained because the tail lights had been on for half the day during the install (the rubber cushion on the brake switch gave out while he was testing it as I have a picture of the car from that morning with the tail lights off..i've replaced that). The battery was turning over the engine just fine for a long time; but got low since lights were draining it so it was too low to test a start after he finished. I bought a new one on his advice...$250 wasted. My original battery charged up just fine and is healthy.    It was running perfectly fine when I messed up the old alarm (programmed out the remotes). He couldnt start it after removing the old alarm; my assumption is that when he unhooked it; he didnt bridge the circuit back when trying to start it. Its always been perfectly fine. The ECU swap and pump were 2 years ago. It's never missed a beat in that time. 
    • This is a big issue for me without the diff. I just have zero drive from the passenger side when drivers side has no traction. Bec's parents place has a crazy steep driveway with odd camber and I have never been able to get up. My bro-in-law's 130i with an (unknown brand) LSD gets up fine as does their dad's Hiace. My car stays at the bottom. We have other odd camber roads around here as we're elevated a bit and if it's raining I can get totally stuck around some hairpins. 
    • Yeah, I am super excited for this.
    • Was the car running before he touched the car?
×
×
  • Create New...