Jump to content
SAU Community

Recommended Posts

I dunno some people might be in the same boat as you Dean so i mean we might have to devide the groups up and have possibly people with an oil cooler and ppl with out so then we can run the groups with the cool lap and the hot lap etc if you get my flow.

If you dont run a cooler, you still can monitor oil temps to a degree (no pun intended).

As oil heats it gets thinner, the thinner the oil, the lower the pressure. If you watch your oil pressure guage, see where it sits after a decent length drive, it should steady out. This is around normal operating temp.

Dont trust your water temp guage alone, it can read full temp, but the oil is still not properly warmed, or it can read normal and the oil is actually getting hot.

enrico, if you get paranoid about the oil cooler the best thing to do is get one :)

At the track there is a lot of waiting time. When you finally get on the track you will get all excited and tend to forget about oil temp/oil problem. Oil will break down at 160 and cause accelerated engine wear according to a Canadian oil journal. However, the general concnesus is that the cooler the oil temp the better. As most ppl stated that the hotter the oil the less protective etc. I get paranoid with oil temp above 130. My last track day, my oil temp was around the 130 and my car has got a factory oil cooler ;) It was warm on the day though. I would not go to Mallala again until I get a extra oil cooler.

Could you pencil me in for Mallala please?

My car hopefully be ready in around a month :(

I'm keen,

I'm not really interested in going flat stick against a clock as I want to get the feel for things first.

Simply push it in to the corners quick then gradually build my speed up.

I don't want to throw a ceramic exhaust wheel just yet. :)

It will be my first time out.

If not I was looking at heading down to a free session by my self.

EDIT: Mid-Semster holidays are approaching so the new motor may be in for a sau track day. :D

mid semester break sounds great

(if it doesn't rain)

here is mallala listed practice day for the next 2 months

JUNE 2004

Saturday 12 Practice (General)

Saturday 19 Practice (General)

JULY 2004

Saturday 10 Practice (General)

Friday 16 Practice (Cars Only)

Saturday 24 Practice (General)

Saturday 31 Practice (General)

Has anyone got any proper timing mechanism....beside stopwatch/mobile phone :) or can get a hold of one?

for 400+kw I think any car will have cooling problems with the stock system copyme :rofl:

which car of your is pushing out 400+kw copyme?

impressive power.....love to see your beast mate!!!!

btw how much will the 34 be on the market for?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
×
×
  • Create New...