Jump to content
SAU Community

Recommended Posts

I've have recently bought a 2009 Premium GTR. As with most, after the initial excitement of the performance wore off, I found myself looking at aftermarket upgrades.

So last week I purchased the following, which are being installed shortly.

Kakimoto Cat Back exhuast system

Titanium Mid pipe

3" Cobb Intakes

BOV's

I also bought a Cobb accessport with TCM. Now I just need some advice as to where is best to take it in the Perth area. A friend recommended I take it to XSpeed but I have since heard that they have gone into liquidation. Is this true?

Also, is there anyone in Perth that has any recommendations or advice on where to go?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/412177-gtr-tuning-perth/
Share on other sites

Thanks for the info, a friend recommended Japanese Performance in Malaga, they can't get me in till Mid November so I will try Fabcar tomorrow.

JPC is where I would take it, Rob and Danny have had a lot of experience with GT-Rs and know what's going on.

My 2 cents.

  • Like 1

I'm not looking for an all out performance tune yet, I'll be treating myself to some more bits in the new year and I will take it to JPC then. I'm currently running an off the shelf tune for 93 so its a little flat, I just want the stock feel back now that I have the noise I wanted!

Bad news, turns out that the dyno room was not ready when I took the car on Monday. Seeing how I'm in Malaysia till the end of the month I will probably book into JPC, see how it goes there instead of Fabcar. The fact that they have a back log is probably a good sign that they know what they're doing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...