Jump to content
SAU Community

Recommended Posts

SOrry to hear...

If I were you I would do one of two things:

1. Build another forged motor - DO IT ONCE DO IT PROPERLY! I would consider buying a bottom end from RIPS

2. Get another OEM RB30E and leave the bottom end. Depending on your turbo and power target it may be more than adequate if you tune safely.

  • Replies 80
  • Created
  • Last Reply

Top Posters In This Topic

I'd be getting them crack tested before using them...otherwise I wouldnt risk it!

Also, I thought we were talking RB30 for some reason in my earlier post (too early in the morning!). So RIPS probably wouldn't be my first option for RB25.

On the otherhand, you could go RB30... :whistling:

Edited by R32Abuser

Yeah wouldn't be using the crank,

The engine builder is blaming it on the old owner for f**king it, etc giving it a hard time when not tune etc, but I think it's got to do with the engine builder and pistons hitting the squiters

Yeah wouldn't be using the crank,

The engine builder is blaming it on the old owner for f**king it, etc giving it a hard time when not tune etc, but I think it's got to do with the engine builder and pistons hitting the squiters

I hope you took lots of photos before you slid those pistons out

I wish I did, but the car is at the shop with the guy that build the motor he was there when found the squiters broken and he said that there was 2mm to 3mm before anything would of hit the squiters and the pistons already came cut out to accommodate the squiters...

As you said I believe the only way squiters could of broke is not enough clearance, but as the engine builder he would be trying to put it on to the other bloke coz he wouldn't wanna folk out money to rebuild the motor... f**king shit

I will have a close look, is this the only way they could break? Think engine builder is trying to say its from too much oil pressure or low oil pressure?

Then he is wrong.

Yes that is the only way they can break other than putting them in incorrectly. If you don't line up the little locator lug they will snap across the banjo part. If the piston hits it, it will snap the stem off and leave the banjo part in tact.

I prob have spares if you need some but I'm guessing you'll need more than just that to get this up and going again

Also....I would be more than happy to inspect any high res photos you can take if you want some advise. I've seen a lot of this stuff before so I can lend my experience if you need it.

I don't have much spare time but if I can help you out I will

Yes that would be great mate, thanks heaps I can already see the engine builder will not say its his f**k up as I'm sure he wouldn't wanna pay for a customers engine to get rebuilt, the squiters are broken clean off from where the bolt is there is only 1 squiter in tack out of the 6

Yeah think so, gonna pull the crank out on Saturday,

#6 rod got really hot it's like a purplely colour where the cap goes over the crank with the bearings and the bearings were f**ked and # bearing was stuck to the crank had to use alot of force to get the bearing out,

With pistons and rods out, engine builder said should be able to turn the crank by the flywheel bolts with ease (two fingers) as when he put it all together with pistons and rods and said he could spin it easey but nope gotta use some force, (big end bearings stuff too)

  • 1 month later...

Has the crank fouled against the oil pump?

Update if anyone is keen,

Yes the crank was fouled against the oil pump it also fouled against the block and girdle, so block and girdle are stuffed, also all bearings, mains and rods are scored and not useable the rods are not useable, oil pump hasn't gave way!!

What I can gather is, n1 oil pump as higher flow then stock and with no oil restrictors, larger sump or head drain while sitting on the limiter has left the bottom end empty and has caused all this damage,

As for the oil jets, there is no marks on the under skirts of the pistons to say the pistons hit it

What I can gather is, n1 oil pump as higher flow then stock and with no oil restrictors, larger sump or head drain while sitting on the limiter has left the bottom end empty and has caused all this damage,

This is completely incorrect.

The N1 oil pump doesn't flow that much and thrust bearing wear isn't caused by oil starvation. The main bearings die long before the thrust side wears out

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...