Jump to content
SAU Community

Stagea Vibration

Import S13

By Import S13,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Import S13 Veteran

Import S13

Posted
Posted

Got a vibration under acceleration and noticeable at anything over 40kmh. This has only started after I had a service and new castor rod bushings, front tyers and front drive shafts.

I've tried putting the same tyers on the back and nothing changed.

Tried pulling the front shaft out and the vibration is gone while it was out but back now that its back in.

All the parts in the front end are tight. The stag is lowered and the new drive shafts sit on a slight lean, can this cause any issue? Can the transfer case cause this issue?

Its a s1 RS4. Cheers

Link to comment
https://www.sau.com.au/forums/topic/412874-stagea-vibration/
Share on other sites
Import S13 Veteran

Import S13

Posted
  • Author
Posted

I have the same rolling diameter all around and all 4 of my rims roll and ballence perfect and they are all the same offset and width.

I had brand new tyers on the back for a month with the fronts being a little older and had no issues.

I then changed to the same brand all around and all are new ATR's on the car with the same size tyers and still have this issue after having the drive shafts and castor rod bushings replaced. I drop the shaft and the problem goes away but I've put it back in as I didn't want to heat up the transfer case too much.

Race__24 Experienced

Race__24

Posted
Posted

I'm pretty sure that dropping the shaft will not heat up the transfer case, in fact it will do the opposite. The rear wheels are constantly being driven by a mechanical connection, a clutch pack is used to engage the front shaft. The clutch packs will be doing less work without the shaft in there.

Bleeding the Altessa system may help. Also using a better oil in there may help.

Import S13 Veteran

Import S13

Posted
  • Author
Posted (edited)

Raised the car an inch and half to level out the BRAND NEW drive shafts. Problem was still there but felt a little better. Shoud also help with the life span of the joints.

Took the new drive shafts out that also had brand new uni joints. Got my old uni joints and found that they where 2mm longer then the new ones which seem to be fine for skylines but not Stageas.

Recond the old joints, fitted them and car feels better than ever. There was enought movement in the new joints to cause a vibration under acceleration. Live and learn.

Edited by Import S13
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

How did you recondition the joints? I thought they were a throw away unit

A lot of joints are not made to be seviceable such as the front driveshaft universals but shops can machine them out and put new joints in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That looks good, but I think you're going to need much beefier side skirts now.
    • GTSBoy
      Most women will agree that parking is the most taxing part of driving

      By GTSBoy · Posted

      They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • GTSBoy
      M35 Brake caliper replacement

      By GTSBoy · Posted

      Define "starting to fail". Wy not just rebuild them?
    • GTSBoy
      S1 rb25/s14 starting problem

      By GTSBoy · Posted

      Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...