Jump to content
SAU Community

Recommended Posts

Battery in the boot is complete!

Had no issues at all.

Here's a few crap night photo's. It tidies up the engine bay alot!

20130125_204811_zps5b5a441d.jpg

20130125_204929_zpsd46e43f4.jpg

20130125_204905_zps8fa6651f.jpg

I didn't get a chance to paint that hold down clamp, that will be this weekends job.

  • Replies 193
  • Created
  • Last Reply

Top Posters In This Topic

Thanks a lot mate!

Yeah dude, that was most of the reason behind moving the battery to the boot as i wouldn't be able to fit a 3.5" intake there. Yeah the whole LHS of the engine bay will become the airbox, so i'll be able to do a nice intake with bugger all radius in the bend, if any at all. Once i get my new intake manifold to suit the Q45 throttle body i'll be starting the intake.

Edited by TimmyMA70

I test fitted my JMR headers today, I wanted to test fit them so i can order all the mandrel bends to make the mid pipe. They had a few minor fitting issues. Nothing I won't be able to iron out though :)

Cylinder 1 pipe was made a little too close to the alternator, we are talking millimeters. So I'll have to heat them up with the oxy and bend them a little.

I had to remove my AC lines to fit them, it was mainly the low pressure line that was fouling. Once I fitted them I put the lines back on, with a slight tweak you could get them to fit again, though I don't think I'm going to worry about it.

20130127_152529_zps90c43ead.jpg

Thanks mate :)

If I eventually get off these 12hr night shifts I'll be able to get a bit more done. The next thing will be a 3" exhaust. I rang all the local exhaust shops and a few in Sydney, though most shops want $900 upwards for a 3" mild steel catback, keep in mind I'll be supplying all my own cat, resonator and muffler.

I thought about it and I might have a go at making my own exhaust. Order all the things I'll need from bestmufflers.com.

My oldies have a workshop with a 4 post hoist and a mig etc. So might give it a crack, I'll think about it for the next few days and make a decision.

Another minor update, it wasn't necessary, though it will make tuning a bit easier.

20130206_194457_zps54fe4e50.jpg

20130206_194357_zps656b8083.jpg

I originally thought the top cam gear was a fake, I later confirmed off RHDJapan that the top cam gear was Tomei's earlier design. So all good :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • If there's enough meat in the housing where you want to put the M12 adapter, then do it, but be aware that if/when you f**k that up you'll probably be repairing it before doing anything else. I'd just drill it out and tap ina 1/4" thread. No need for rocket surgery when the next most obvious thing will do. You could throw a 1/4 x 1/8 bush in there and use the same fitting you intended to use.
    • Is the only issue that the oil catch can is getting filled on hard runs? I'd be thinking more about oil control issues rather then the head lifting, especially as you aren't seeing spiking in the coolant pressure.  Do you need restrictors in the head, or better drains from the head? Does the sump need venting to the catch can?
    • Tried to make 1/8npt threads into compressor house of the turbo for my EBC. Threads got fu#ked and ended up with and elongated hole, so I do have good amount and nice threads 90% of the hole but 10% I only had 1-2threads there and rest of it is flush on that side of the hole.. So my idea is to do M12 x 1.25 to AN4 with braided lines instead of 1/8npt to 4mm vacuum silicone hose.  and hopefully get a better thread. M12 is quite big and AN4 is a little bit bigger than 4mm (4.9mm inner diameter braided PTFE hose). but this should work. Thoughts? Otherwise I will weld and adapter onto the turbo.   
    • Looks great, I hope everything is working well after all that time!
×
×
  • Create New...