Jump to content
SAU Community

Recommended Posts

Hi guys,

I was wondering if there existed a stencil for the ARC symbol for intercoolers.

I have a twin entry M079 ARC intercooler for a BNR34 but as you can see from the image below, the symbol has faded quite a bit. Although, it did start off as white colour.

I know I can print one out, but to get the exact height, width etc would almost be almost impossible.

cooler-1.jpg

Wouldn't be too hard David.

Gave you got a sticker guy down there? They could measure it up and do their thing.

Measure the entire grill area and locate where the ARC stands. Then they print out a vinyl stencil cut out, spray away.

I wouldn't mind getting hold of the template if you can get one done aswell. You can't even make out the ARC letters on my cooler.

Also, just out of interest - have you got your bov's plumed back with this set-up and what intake set-up are you running? (stock box/pods/arc box etc)

Edited by wedge_r34gtr

Someone do the stencil thing as Owgasm recommended please and I'll buy it haha.

I've emailed ARC brazing to see if they can provide a stencil, but I highly doubt the chances of that happening.

if you can still make out the writing (you can on yours, but this comment is also for others wanting the stencil as well), simply mask up along the edges of the writing (and then tape up some newspaper obviously) and then you can spray it. just do a few light coats to minimalise the spray getting in under the tape between the fins.

you could also make a stencil for future use if you wanted. simply mask it up, get a sheet of clear contact or sticker vinyl, stick it over the tape, get a craft knife and run it around the inside edge of the tape (making sure to leave little tabs to the inside of the A and the R so they always go back in the same spot every time). then pull it of and stick it back onto the backing, or some thin plastic. then simply cut out the stencil. or simply trace around on some tracing paper after masking up, and then you can trace it onto some contact to stick on next time you want to paint it.

Also need some hard pipes on that twin entry ;)

yeah, it's just not in the photo. The cooler and hard pipes are both on the car atm :)

if you can still make out the writing (you can on yours, but this comment is also for others wanting the stencil as well), simply mask up along the edges of the writing (and then tape up some newspaper obviously) and then you can spray it. just do a few light coats to minimalise the spray getting in under the tape between the fins.

I'll guess I'll try to do this first! Use masking tape, as making a stencil seems pretty hard. Although I guess the issue would be getting the curved edges to be exact. I guess I'll do a DIY if I try it and turns out something like this!

0714.jpg

Edited by kylieyeah

making a stencil is pretty easy, get someone to load the vector up and print it to the correct size, , mark it up on some manila folder material etc, cut it out with a sharp blade, stick it over and spray it.

Okay guys! This method about making a stencil would be great!

If someone would like to make one, I will happily chip in with them and help get it made up. I just dont have any hook ups to a sticker/stencil maker or anything.

Would be great if someone could organise! I'm very keen on getting this ARC symbol looking new again and will do whatever is reasonable! :)

yeah, it's just not in the photo. The cooler and hard pipes are both on the car atm :)

I'll guess I'll try to do this first! Use masking tape, as making a stencil seems pretty hard. Although I guess the issue would be getting the curved edges to be exact. I guess I'll do a DIY if I try it and turns out something like this!

0714.jpg

if you use a thin tape to tape it up you should be able to get the curve right, as well as cutting it with a craft knife

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...