Jump to content
SAU Community

Recommended Posts

Next couple of weeks...

Gearbox will stay with the car but motor and every aftermarket part will be up for sale but motor wont be cheap.

  • Replies 86
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Are the sub frames in good nick and non accident damage ?? Also no rust ?? and how much for them.

I'm about 20 mins from Nerang so if ok be keen to have a look at them plus shocks.

I'm just after bare subframes as dont need brakes etc.

Cheers

Marcus

Any reason for delay in selling motor?

Are you getting it refreshed or something?

No not getting refreshed as brand spanking new and only had run in tune.

I'm just busy with new business and no time for a few weeks.

Nismo and Takata harnesses SOLD

STILL AVAILABLE

ENKEI RPO5 RIMS 18 x 9J x 25 x 5-114 Price $3,000 (still available)

SUPERIOR AUTO CREATIVE CARBON SHIFT PANEL : $195 (still available)

TOP SECRET CARBON COIL PACK ORNAMENT : $120 (still available)

NISSAN GENUINE BCNR33 BONNET HINGES $100 Brand new unused.

CARBON GRILL BCNR33 ONLY and NEW GTR EMBLEM BCNR33 ONLY $300 Brand new.

  • 1 month later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...