Jump to content
SAU Community

Recommended Posts

  • Replies 96
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Throttle behaves however you want it to behave.

There is table in there that you can adjust so that any tiny bit of pedal means full throttle. Obviously you don't want that, but it's the example.

That being said, uprev provide some values in a little switch box, and seems the best option.

Make sure they also bring the thermos on sooner in the map, good for the motor and power.

Thread is useless without results!

Link to comment
https://www.sau.com.au/forums/topic/414711-uprev-reflash/#findComment-6650784
Share on other sites

Apologies for the late reply everyone. Car is now running sooo amazing.

Started of running around the 150rwkw (running really rich, and was fixed by a MAF clean) Base line was then achieved of 161.8rwkw. After this then tuned for 3rd and 4th gear (being 6MT) Dyno charts show the improvements. Overall the final chart showed gains of up to 50nm of torque (main aim) and 10-15rwkw) So after working it out I saw 10% power increase and 15% torque gain.

All I have done so far is a Takeda Short Ram intake, and a custom "catback" with a hotdog resonator through to twin outlets (with small mufflers). Soon to come will be pulleys, plenum spacer, ceramic coated headers new custom high flow cats and Y pipe and eventually some BC high lift cams.

Took it for a spin up Nebo and Glorious today, even in the mid 30's it pulled sooo much better and the throttle response has improved immensely. All in all. 10/10 for customer service through ECC and definitely worth every cent.

Vid of the run.

Edited by Vthirty5
Link to comment
https://www.sau.com.au/forums/topic/414711-uprev-reflash/#findComment-6650796
Share on other sites

Thanks mate, im stoked. I got it as a discounted rate as I was informed that I was the first customer to use their UpRev software. I think they have a couple more spots left for a $500 rate, then it will go up to the normal rate which is 990 i think.

Link to comment
https://www.sau.com.au/forums/topic/414711-uprev-reflash/#findComment-6650884
Share on other sites

I bought an UpRev tuners package about a year ago and got a tuner to give it a go. Might try East Cos tCustoms to give it a retune, see if they can get better results. I get around 171KWs as an 5AT, but my modlist seems a little bit bigger than yours, although you are a 6MT.

Link to comment
https://www.sau.com.au/forums/topic/414711-uprev-reflash/#findComment-6651116
Share on other sites

That is impressive, i am loving the feedback ECC's customers are giving it makes me want to be in Brisbane even more now!

For $500, that's is excellent value for money considering how impressed you are of the results.

Good stuff!

Link to comment
https://www.sau.com.au/forums/topic/414711-uprev-reflash/#findComment-6651168
Share on other sites

I have fairly similar mods to your Sheldon and mine makes 184rwkw (on a very conservative Mainline dyno) with just an SAFCII. I would definitely get yours retuned.

Will look into it, just have to weigh up if its worth it since im still trying to sell.

Link to comment
https://www.sau.com.au/forums/topic/414711-uprev-reflash/#findComment-6651291
Share on other sites

Not wanting to steal the thread, but I am not 100% on that for all models;

Am 99% certain my manual coupe has an open diff and uses the brakes to prevent wheel spin/oversteer (even with traction control disabled)

Anyone got a good way to check?

Brake LSD?

The manual V35 uses a viscous unit Inside the diff, like the 350z.

Link to comment
https://www.sau.com.au/forums/topic/414711-uprev-reflash/#findComment-6651432
Share on other sites

Not wanting to steal the thread, but I am not 100% on that for all models;

Am 99% certain my manual coupe has an open diff and uses the brakes to prevent wheel spin/oversteer (even with traction control disabled)

Anyone got a good way to check?

Jack up the car with both back wheels off the ground, release the hand brake and ensure it is in neutral, turn one wheel, if the other wheel turns the same way, you have an LSD, if it turns the opposite way you have an open diff.

You can also just jack up one wheel, with the handbrake off, and in neutral, the one wheel off the ground will be difficult to turn, unlike an open diff, which doesn't offer much resistance.

Link to comment
https://www.sau.com.au/forums/topic/414711-uprev-reflash/#findComment-6652012
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...