Jump to content
SAU Community

Recommended Posts

Thought id post this up incase anyone was wondering. $85k for the base G37. Less then i expected, but still too much..

Further to my previous correspondence, I have attached a pre-launch brochure for you for now and hope to have the full brochure, with specifications, available within the next 10 days.

Pricing was released this week for the new model and is set at $84,970.00 for the GT Premium Coupe, $92,950.00 for the S Premium Coupe and $97,570.00 for the S Premium Convertible; these figures all become more impressive when I highlight that they are inclusive of all on road costs making the G Coupe and Convertible extremely compelling alternatives to the status quo.

Our demonstration models arrived yesterday and are available to drive at your convenience.

I will be in touch throughout the week to see if I can help any further; please let me know if I can answer any questions or help to arrange a drive for you at any stage.

Many thanks,

Bla Bla

Infiniti Centre Sydney

Still a rip off.....

See how much they cost in the US of A.

You can't compare them to what they cost in the US, everything is cheaper in the US. A 335i doesn't cost a hell of a lot more than a G37 in the US but they are well over $100,000 here.

more likely that their market is much much larger leading to better economies of scale and increased purchasing power for the consumer.

But probably the biggest impact on pricing in Australia is the 30% LCT (luxury car tax) we put on top of the 10% GST tax - that's 40% of the cost of the car in taxes alone.

more likely that their market is much much larger leading to better economies of scale and increased purchasing power for the consumer.

But probably the biggest impact on pricing in Australia is the 30% LCT (luxury car tax) we put on top of the 10% GST tax - that's 40% of the cost of the car in taxes alone.

It's actually 43% total increase. 30% LCT is added on the the sub total to which 10% GST is added.

Hence, vehicle = $100k. Multiply by 1.3 for LCT (130k now). Then multiply by 1.1 for GST. Therefore total cost of vehicle is now $143k.

There are ways around that, but that's another story....

At the end of the day, stuff costs less in the US because they have a lower cost of living and hence salaries are lower - in general.

We assist in placements in the US from time to time and you'd be astonished as to what the differnce can be.

For mine, not only is the initial buy in a concern but I would suggest the residual value after the warranty expires will be nowhere near the likes of a high end 3 series coupe. But I suppose these cars may well be purchased by business customers who can offset this via depreciation.

Infiniti (or its distributor) really need to get its pricing right as price reductions later on down the track is akin to burning bridges with existing customers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...