Jump to content
SAU Community

R32 Gtr Dash Vents

Anfanee

By Anfanee,
in Australian Capital Territory

 Share

Recommended Posts

Sinista32 Grand Master

Sinista32

Posted
Posted

Anthony - come pick the dash up and pay later (i need space)

As for the vents - if your going to replace them just pull them out.

Centre one has 4 clips top and bottom, Passenger has 2 clips top and bottom.

See pic.

Newies will slide in and clip into place.

The screws I saw previously just hold the AC/Heater plastic piping behind the vent to the dash. Dont actualy screw into the vents.

My pics comming tomoz

r32centrevents.jpg

Sinista32 Grand Master

Sinista32

Posted
Posted

yep that would be a bonus Anthony.

Just need to be certain you take the ones for the stock fuel rail and I keep the aftermarket fuel rail ones :).

Should be easy to determine.

Call me on 0408 732 655 when you get to the pine Island turn-off :thumbsup:

D.I.Y. Mik Veteran

D.I.Y. Mik

Posted
Posted

I have a set of fairly new vents in the car (bout 1 year old) i sort of dont need them anymore as the ducts are not hooked up anymore.

The only problem id have with selling them is what do i put in the holes in the dash? i cant think of anything easy that would look ok.

If you have a solution ill sell them to you cheap.

Brand new ones out of the box are better so do that if you can afford it. Like in Sins pic you can see the plastic bag, fresh produce!

Sinista32 Grand Master

Sinista32

Posted
Posted

lol - I dont usually answer an unknown number when getting sex. However it all worked out.

Thanks for helping clean up my garage :) You have a very nice GTR there :thumbsup:

Actually you interupted my BLT in the garage. Phone was in the bedroom :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • R34_GT to Turbo
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By R34_GT to Turbo · Posted

      Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a good German place in Brisbane if youre up for the drive 😛
    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...