Jump to content
SAU Community

Recommended Posts

1990 R32 4 door (sunroof model) Imported 3 years ago so its got the side indicators

M spec

Factory turbo

Factory manual

Red

2 wheel drive

Mods:

Exterior

Custom side skirts

Sunroof

Genuine weather shields (ones cracked)

Interior

Apexi Power FC + hand controller

HKS EVC 5 boost controller with digital display

Apexi boost guage

Apexi pen style turbo timer with afr and valtage meter on it

Decent Keenwood headunit with leads to the boot for amp (no amp included)

Engine

Internally standard RB20 rebuilt last year (new headgasket and all new belts done at the same time)

Custom built turbo by bill at ATS High flowed OP6 turbo with a huge front alloy wheel

Adjustable sard fuel presure reg

Trust greddy front mount

Earls oil cooler and relocator

Apexi power intake

Brake master stopper

Walbro fuel pump

3" trust exhaust from the dump back (standard dump on atm) + high flow cat

Suspension + handling

Front npg Coilovers

Rear isc coilovers

Rear camber arms

Hicas lock out bar

Heavy duty whiteline sway bars front and rear

Front and rear strut braces

Adjustable front tie rod ends

Adjustable front castor arms

All new nolathane bushes throughout the car

PRICES

The car is currently defected.

You can either take it as it stands (defected) with factory everything swapped back in EXCEPT ecu, Injectors and AFM. (i have injectors and AFM you can have) Along with all the mods, except power fc. (bring your own ecu or I'll take it after you drive it home)

$6800 ono

The same as above without all the goodies.

$4200

OR I will part the following itmes.

Apexi Power FC + hand controller $1000

Earls oil cooler and relocator $150

Front npg Coilovers $450

Rear isc coilovers $450

Rear camber arms $120

Front strut brace $100

Rear strut brace $100

Adjustable front castor arms $200

Genuine nismo thermostat $100

Prefer text instead of PM 0401485975. Text me for more pics.

0247kmg_20.jpeg

3829k23_20.jpeg

366614k_20.jpeg

Edited by InTrenches
Link to comment
https://www.sau.com.au/forums/topic/414907-sa-hcr32-4-door/
Share on other sites

Price drop! Defected with Full Trust (jasma) exhaust, turbo, GTR injectors, FMIC, blitz pod, apexi mechanical boost gauge, apexi pen style turbo timer hooked up to O2, A/F ratio, Batery etc. GTR front bar, skirts and pods, Greddy air splitter (bonnet catch), sway bars, Pioneer head deck and speakers throughout, wiring for sub/amp in boot. Can come with power FC for an extra $1,000.

$3990 ono

Link to comment
https://www.sau.com.au/forums/topic/414907-sa-hcr32-4-door/#findComment-6659834
Share on other sites

Underneath is very clean. Just had all the chassis rail CAPPING re-done and someone tried to jack it from there and dented them.

The sunroof only pops but doesn't retrack and the drivers side window switch is missing some switches but still fully functional.

Link to comment
https://www.sau.com.au/forums/topic/414907-sa-hcr32-4-door/#findComment-6684691
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...