Jump to content
SAU Community

Rb30 Short Motor Awd Inc Ati Diff & Tomei Pump

HKS26T
 Share

Recommended Posts

HKS26T Experienced

HKS26T

Posted
Posted

Hi guys,

more moving to free up some space and $$

motor has only seen 50kms....bought it off a mate that needed money desperately...

well over $15K to replicate

1. CP Pistons 86.5mm

2. ARGO forged rods (23mm gudgeon pin)

3. Nitto Metalhead gasket and crank collar

4. Pro engine 4WD adaptor

5. Trust extended sump with ATI FRONT DIFF

6. TOMEI oil pump with modification for additional external pickup

7. Prepped concrete block, Prepped crank machine balance etc...

8. 1/2 inch ARP headstuds

9. ATI 1000hp balancer

This is a motor that i would have no hesitations using as is (without stripping down)

$9.5K

Cheers

Steve

HKS26T Experienced

HKS26T

Posted
  • Author
Posted

I have received a few pm'z in regards to splitting ext bits to the short block....

1. Tomei oil pump

2. Ati balancer

3. Sump with front diff

I will consider if there is enough interest but not at this stage... Pm offer and contact number so i can keep order and track :cheers:

Shoota_77 Veteran

Shoota_77

Posted
Posted

Any info on the ATI front diff?

LSD?

Tried Googling but couldn't find any info on ATI doing anything other than gear sets for Ford diffs!

HKS26T Experienced

HKS26T

Posted
  • Author
Posted

What sort of money you chasing for it...?

for? if sump alone? then i'm not sure.... pm with a offer and i ill have to work out whether its worth parting the package out.

(there is a final number i wish to get for everything)... probably have individual prices for everything in a few weeks.

thanks

HKS26T Experienced

HKS26T

Posted
  • Author
Posted

Lmao

before making a $600 offer for the sump

This is how much it would cost you to do yourself

Used sump $250

Trust extension $450

Remove diff to weld $50

Weld $400

Ats front diff $1850

Install diff $250

Oil $100

Now think If you wanted to sell this how much would you offer?

:P

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...