Jump to content
SAU Community

Recommended Posts

Gday,

All prices negotiable. Pick up preferred from Beaudesert Qld, but willing to post if needed. All parts are used and from c34 s1, s2 and 260rs. I work long hours so don't expect an instant reply but I'll do my best.

Thanks for looking.

post-58649-0-32984300-1355125119_thumb.jpg $100 - Dash mat

post-58649-0-90000500-1355125127_thumb.jpg $100 - Complete genuine floor mat, drivers worn.

post-58649-0-65876600-1355125131_thumb.jpg $150

post-58649-0-25030400-1355125262_thumb.jpg $100

post-58649-0-85524700-1355125025_thumb.jpg $20 - For rb25det - not direct fit though

post-58649-0-29956300-1355125021_thumb.jpg $5

post-58649-0-24935400-1355125033_thumb.jpg $20 - S1 woodgrain

post-58649-0-55925900-1355125036_thumb.jpg $10

post-58649-0-23322000-1355125040_thumb.jpg

post-58649-0-50411400-1355125046_thumb.jpg

post-58649-0-87990900-1355125042_thumb.jpg $150

post-58649-0-18872000-1355125053_thumb.jpg $100 - HICAS lock

post-58649-0-08655900-1355125061_thumb.jpg $20

post-58649-0-48774400-1355125067_thumb.jpg $20

post-58649-0-42245000-1355125099_thumb.jpg

post-58649-0-74881100-1355125102_thumb.jpg

post-58649-0-02476000-1355125105_thumb.jpg $150 - Brembo rotors (machine recommended), nismo rear/ compliance front pads with decent meat

post-58649-0-83845400-1355125108_thumb.jpg $10

post-58649-0-69370500-1355125112_thumb.jpg $20 - Top and bottom rad hoses. red silicon (photo is bad) off an rb26 prob fit rb25?

post-58649-0-93961800-1355125133_thumb.jpg $50 - rb26, where running 360+ hp fine when removed

post-58649-0-69625000-1355125137_thumb.jpg

post-58649-0-14944000-1355125222_thumb.jpg $50 - Walbro gss 342, only used for 5000km

post-58649-0-77815100-1355125229_thumb.jpg $5

post-58649-0-14300500-1355125232_thumb.jpg $5

post-58649-0-16237100-1355125239_thumb.jpg $20

post-58649-0-36344300-1355125244_thumb.jpg $20

post-58649-0-38855900-1355125249_thumb.jpg $5 - hks oil filler cap

post-58649-0-35705500-1355125254_thumb.jpg

post-58649-0-66901200-1355125259_thumb.jpg $100

Link to comment
https://www.sau.com.au/forums/topic/415320-some-random-c34-crap/
Share on other sites

Brembo rotors (machine recommended), nismo rear/ compliance front pads with decent meat

what size are the rear rotors?

and is the boost controller electronic ( i guessing not by the looks of it ) and if so dose it work all good? and so u have all the bits?

Edited by whitenight27

what size are the rear rotors?

Rotors are the standard r33 gtr brembos

Rears: 300mm

Fronts: 324mm

Dash mat SOLD

Boost controller SOLD

Oil cap SOLD

Console tray SOLD

Coil packs SOLD PENDING PAYMENT

Silicon Radiator Hoses SOLD PENDING PAYMENT

Woodgrain center console & stereo surround SOLD PENDING PAYMENT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
×
×
  • Create New...