Jump to content
SAU Community

Recommended Posts

mine has kind of a miss fire, boost drop, flat spot when flat out, havnt had it in 1st or 2nd, happens around 4 thousand... changed the plugs, not as bad but still there.. any ideas?

Yeah can't expect magic out of tuners sometimes some issues are weird and they have not experienced it. I bought some coils off jessestreeter since they're new I'll start of at the biggest gap 1.1mm if it misses go down till it doesn't. Bcpr7es

Zeb its 16psi dropping to 14.

oops 2 convos going at once

Bryce, what ECU? What have you done (for me) lately....eddiiiiieeeeeee

Played with intake piping at all? where and how does it cut?

Rob/New Guy

Not enough for R&R, Id say coils are past their best

oops 2 convos going at once

Bryce, what ECU? What have you done (for me) lately....eddiiiiieeeeeee

Played with intake piping at all? where and how does it cut?

Rob/New Guy

Not enough for R&R, Id say coils are past their best

f**k YOU EDDIEE.

Half yo shit.

This is 0.8mm gap? No extra digits after bcpr6es like 11?

Could be Coilpackssss.

or fuel related etc. ie, shit/low octane, old fuel filter etc etc...

or timing...

complicated beasts.

+ Penile ECU.

not that I know of.. im preety sure its just bcpr6es, ill see if I have any of the packets laying around haha,

when I start working again ill do the coils and ecu?

Likely 0.8mm gap then.

Full ECU replacement will do much.

Piggyback like my SAFC will do a bit less but Bang for Buck I think is worth it.

Get you P's, coils and 10psi. That is a good start without the ECU cost.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...