Jump to content
SAU Community

Recommended Posts

Over the weekend, for Skywagon I made an exhaust shield for the Extractors. (Doubles as a BBQ.)

post-78856-0-90750700-1393234002_thumb.jpg

I also tinted the indicators. (way too dark)

post-78856-0-66564500-1393233984_thumb.jpg

and installed some New Bonnet stops as per Ebay again ---> http://www.ebay.com.au/itm/330892988661?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649

Today on the 33 I replaced my Pedders Shocks & Stock Springs with other Pedders Shocks and NISMO Springs. :woot:

post-78856-0-70844800-1393233999_thumb.jpg

Harder Ride and 10mm lower.

(feels so Boy Racer Driving round with no back seat and lots of extra fuel pump and exhaust noise.) :woot:

  • Like 1

After messing round with castor arms on the Wags and finding 2 different size bush spacer dealies in there, I put 2 same size ones in.

Got a Re alignment this arvo and suddenly my steering wheel is straight and much less Tramlining. :woot: Much Better.

Received in the mail today (All from 1 Ebay seller)...

2 RB30 AFMs, 1 Coil, Brand New Eagle Sparkplug Leads and a 12 pack of New KLG Sparkplugs.

Installed LED Rear brake lights, Indicators and number plate lights... The color in the brakes and indicators is so much more vibrant. Looks better than new!

post-92069-0-50929600-1393411484.jpg

So finally i got my car running now time to get it tuned and also does anyone knows how much will it cost to get all my exhaust studs replaced.

post-72907-0-56590400-1393490257_thumb.jpg

Just waiting on some hoses and then i will tidy all the hoses

you can go to speciality fasteners they have good stuff. You can probably do it yourself if you do it slow. If you snap any buy a reverse drillbit about half the size the diameter for the bolt. soak it in release agent a few days before you remove it but you cant drive coz it'll heat it up again.

Installed a blitz return flow today. Great kit, real easy to install. Only cutting required was some trimming of the front bar

Oooh.. Nice Work. :D

How's it feel to drive? More power? Response slower or not?

I felt a big difference in power / airflow when I put in the R34 GTT smic after the stocker...

Changing from the GTT to the ARC smic was not so noticeable.

Oooh.. Nice Work. :D

How's it feel to drive? More power? Response slower or not?

I felt a big difference in power / airflow when I put in the R34 GTT smic after the stocker...

Changing from the GTT to the ARC smic was not so noticeable.

Year I think maybe I've lost a bit down low, gained a little mid range but it's definitely freed up top end.

Another supporting mod done. Been talking to dvs Jez lately, hopefully POWER :woot: isn't too far away :D

  • Like 1

Nice work Chris

you can go to speciality fasteners they have good stuff. You can probably do it yourself if you do it slow. If you snap any buy a reverse drillbit about half the size the diameter for the bolt. soak it in release agent a few days before you remove it but you cant drive coz it'll heat it up again.

Will give that a try maybe next in line and if not then just give it to a exhaust shop to do it.

Today i tidy the engine bay a little and got rego :banana:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...