Jump to content
SAU Community

Recommended Posts

Unless otherwise stated, all items are 732 Nissan Black Metallic.

Item 1: R32GTR Nismo ORIGINAL side skirts - without front guard 'cap' section. Use your standard one; they're the same.

Condition: Very good, but needs repaint. May need to bolt as well as sikaflex onto rear guard

Price: $500.

Postage: No, pick up only inner North, Melbourne

Contact: PM me

Pics: as below.

IMG_4384.jpg

IMG_4386.jpg

IMG_4388.jpg

IMG_4390.jpg

IMG_4392.jpg

IMG_4394.jpg

IMG_4396.jpg

Item 2: R32GTR Nismo replica bonnet lip, fibreglass

Condition: Excellent, does not need repaint. Attaches via double sided tape and 4 screws.

Price: $120 or offer.

Postage: No, pick up only inner North, Melbourne

Contact: PM me

Pics: as below.

IMG_4376.jpg

Item 3: R32GTR original factory side skirts in SILVER.

Condition: Good, but needs repaint.

Price: $120 or offer.

Postage: No, pick up only inner North, Melbourne

Contact: PM me

Pics: as below.

IMG_4398.jpg

IMG_4400.jpg

IMG_4378.jpg

IMG_4380.jpg

IMG_4382.jpg

Item 4: Factory R32GTR bootlid

Condition: Good, but needs repaint.

Price: $100 or offer.

Postage: No, pick up only inner North, Melbourne

Contact: PM me

Pics: as below.

IMG_4402.jpg

IMG_4404.jpg

IMG_4406.jpg

IMG_4408.jpg

Item 5: R32GTR driver's side mirror.

Condition: Very good, does not need repaint. All motors worked when removed.

Price: $50 or offers.

Postage: No, pick up only inner North, Melbourne

Contact: PM me

Pics: as below.

IMG_4410.jpg

IMG_4412.jpg

Hi, I'm very interested in the r32 Gtr n1 Nismo side skirts. I would like to know if there's anything broken/repaired ?? ( other than small scratches )

If you say that everything is ok and there's no major damage with the skirts like ripped screw holes in the plastic , I'll take them .

I can send you payment on the 10th jan via PayPal .

Send me your PayPal address.

Thanks

Gabriel

Mirror SOLD

Nismo skirts PENDING transfer

Roy: if you want to dummy fit them to the side of your thing message me and come over we can hold them up to see if they fit...

Keen to but the prob is of course it means I have to remove the skirts currently one the car, complete with double sided tape etc etc which is a head fark to get back on properly

:thumbsup:

Will be putting the new vents in my Dash when it arrives. Before putting it in the car.:)

Going to be a nightmare pulling my existing one out from what I've heard. A lot of this maybe :rant:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity.
    • 100% the factory sender is tapered, that is how it seals (well, that and teflon paste or tape)
    • Thanks folks - I've saved a few links and I'll have to think of potential cable/adapters/buying fittings. First step will be seeing if I can turn the curren abortion of a port into something usable, then get all BSPT'y on it. I did attempt to look at the OEM sender male end to see if it IS tapered because as mentioned you should be able to tell by looking at it... well, I don't know if I can. If I had to guess it looks like *maybe* 0.25 of a mm skinnier at the bottom of the thread compared to where the thread starts. So if it is tapered it's pretty slight - Or all the examples of BSPT vs BSPP are exaggerated for effect in their taper size.
    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
×
×
  • Create New...