Jump to content
SAU Community

Recommended Posts

It's got less kms than your motor, so should by all accounts be in better condition. If you are doing that, put a little amount of copper seal around the plug Seals.

I think there is a rubber line outer seal to replace too, that sits in the cover? Scotty? Should only be a couple of bucks.

Link to comment
https://www.sau.com.au/forums/topic/417327-my-pnm35/page/8/#findComment-7205239
Share on other sites

Yeh, the rocker gasket is around $25.

I don't like putting sealant around them, as a thin smear might fall off and partially block the oil pump or pickup (as there is nothing to hold the sealant in place). I try to minimise the use of silicone inside the engine for this reason.

Link to comment
https://www.sau.com.au/forums/topic/417327-my-pnm35/page/8/#findComment-7205256
Share on other sites

Should tell nissan that... Whole thing is held together with sealant! :P

I never had an issue with it when I was changing sumps over. No sealant disappeared. As long as the instructions are followed, the stuff works well.

If you use tons of it, and clamp it down hard immediately, then your right, you're in for a bad time.

Link to comment
https://www.sau.com.au/forums/topic/417327-my-pnm35/page/8/#findComment-7205318
Share on other sites

I will say it again for the deaf among us... There is nothing to hold the sealant in place, and nothing to clamp it.

As the tube is covered in oil the sealant won't stick, and there isn't another mating surface to hold it in place, hence why it will break off and float about the engine. It's a slightly different application to sealing the sump as there is a 20mm lip holding the silicone in place, plus you would be able to scrape it clean first and brake clean it.

Link to comment
https://www.sau.com.au/forums/topic/417327-my-pnm35/page/8/#findComment-7205325
Share on other sites

I see what Scotty means.

The sealant wouldn't help. It's just a thin metal edge.

Yes, but Nissan still used a little sealant on the cover gasket, at least mine had some when I removed it. Someone should tell those engineers the theory & see what they think....

On sealing around the spark plug tube, totally agree - it's pointless. Better to syringe it out every so often than risk it.

Edited by Commsman
Link to comment
https://www.sau.com.au/forums/topic/417327-my-pnm35/page/8/#findComment-7205404
Share on other sites

Yes, but Nissan still used a little sealant on the cover gasket, at least mine had some when I removed it. Someone should tell those engineers the theory & see what they think....

On sealing around the spark plug tube, totally agree - it's pointless. Better to syringe it out every so often than risk it.

It would have just been nice for them to just round off the spark plug tubes at the end to just a little flat surface, so it would seal better. But alas, I suppose the accountants got in their ear. Probably one of those will it last 3 years/100k kms things. Even the old honda I had (honda boi!) had a better mating surface.

Link to comment
https://www.sau.com.au/forums/topic/417327-my-pnm35/page/8/#findComment-7205433
Share on other sites

It would have just been nice for them to just round off the spark plug tubes at the end to just a little flat surface, so it would seal better. But alas, I suppose the accountants got in their ear. Probably one of those will it last 3 years/100k kms things. Even the old honda I had (honda boi!) had a better mating surface.

How do you deal with no vtec? It must be so boring driving your s13.

Link to comment
https://www.sau.com.au/forums/topic/417327-my-pnm35/page/8/#findComment-7205494
Share on other sites

Hahahahahah

My little shitbox didn't even have vtec! It was a uni student car.

I think it was before the whole vtec fan boi thing. The vtec models were pretty expensive in 2002, so kids couldn't afford them.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/417327-my-pnm35/page/8/#findComment-7205499
Share on other sites

  • 1 month later...

Nup, it was actually on the quarter mile it blew up.

The motor was suffering massive amount of Det, and was shedding the electrodes from spark plugs. One may have come off and rattled around, but it looks as if the det blew out the side of the piston rings too. You'll see more once you remove the piston and rod.

Link to comment
https://www.sau.com.au/forums/topic/417327-my-pnm35/page/8/#findComment-7234469
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...