Jump to content
SAU Community

Has Anyone Gone To Pulse Racing

WARLORD

By WARLORD,
in New South Wales

 Share

Recommended Posts

Cherry Racer Collaborator

Cherry Racer

Posted
Posted

My personal experience is that Paul had been round a long time and knows his stuff.

I took my car there when they had a $50 dyno run offer. They let the car heat up then showed me the problems with the mapping and that it only made 175kw atw

Cherry Racer Collaborator

Cherry Racer

Posted
Posted

Sorry, stupid iphone. My experience was with an STi...

As I mentioned above, he let the car heat up and didn't cool it properly so the computer pulled timing and only made 175kw atw. The car had previously (and did in the future) produce 210kw and ran perfectly. He then showed me the read out and explained how it could be improved.

I worked this out further down the track but in my opinion its not the most honest way to do business or get work.

As I mentioned though, he has been around a long time and should know his stuff.

  • 2 months later...
WARLORD Veteran

WARLORD

Posted
  • Author
Posted (edited)

no !!!! paul is good at what he does but i should of stuck to what i know as he is tooo bizzy bizzy

Always two sides to a story.....

do you know the story !!! be for you jump in

Edited by WARLORD

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Valve clearance for RB25det series 2

      By Duncan · Posted

      Its also worth mentioning that 30 years after it left the factory and god knows how many missed oil changes since, there is every possibility that one or more lifters are ticking because they are sticky/gummed up. To resolve that you need to pull the cams then pull each lifter, disassemble, clean, reassemble, soak in oil and re-install, and they should come up good as new.
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      What air filter are you running? Is it a panel filter in the stock air box, or a pod filter? Is the air filter the type that is oiled?   If you unplug the IACV, what rpm does the engine idle at?
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • Dose Pipe Sutututu
      Valve clearance for RB25det series 2

      By Dose Pipe Sutututu · Posted

      This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
×
×
  • Create New...