Jump to content
SAU Community

Recommended Posts

Hello,

Back in November I took my car to the tuner.

I am running a power-FC on a 1998 r34 GT-T RB25DET NEO

550 injectors

GT-RS turbine

poncams

Z32 MAF

The car came back but has had issues running very rich (10.0) when cold to 50 Celcius

Once warmed up around 80C the car runs fine (idle 14.7) except that when you punch the gas it studders then engages.

I took the car back to the tuner and he says that it is having an issue he has never seen before. On the data logger when you push the throttle there is a momentary drop in AFM voltage then it raises as it should.

The MAF is brand new and has been tested as fine in another vehicle. All of the other parts are also brand new. Also the engine was just rebuilt.

I went to pick up the car today from the tuner again because he can't seem to figure out the problem. He left me a note that said that he had noticed something. If the car is not turned on and you depress the peddle the AFM voltage and the throttle voltage rise together and at exactly the same value. It seems there may be a crossed wire somewhere or maybe it is supposed to be like that. He said to check the harness. I was wondering if anyone else has heard of a issue like this before. After the initial pause the engine runs fine. It is just the initial push that has problems. Thanks.

Link to comment
https://www.sau.com.au/forums/topic/418113-r34-maf-voltage-issue/
Share on other sites

agree. MAFS-1 should not change when the car is off and you press the accel pedal

cant be too hard to trace the signal wire when it was spliced at the afm plug, this is where its likely to be wrong

before you go looking at all the wiring... have you tried a brand new battery... reason for asking is if it has dropped a cell or 2 then there might not be enough amp's running though...

very simple thing to test and rule out before going to the effort of wire hunting... poor battery can lead to a lot of issues people dont consider...

Yeah, but hard to imagine low battery voltage causing the signal from one sensor to appear on the wiring for another.

agreed.. but think about a bad battery and all the warnings a dash will show... i had a bad battery show the oil light, park brake and light bulb warning... replaced battery and all fixed...

as bad battery can show up random things and is a simple thing to check which requires minimal effort... even just leaving the battery on charge over night and check again in the morning... cost nothing to rule it out :)

I ran new wires from the MAF directly in to the ECU ports for AIR signal and Signal ground. Same result. So it is not the wiring harness. Does anyone else have a Power-FC in a ER34 that can try this out. Turn the car to on but not engine running put the PFC into monitor mode for AFM and watch the voltage whilst pushing the gas pedal. Any help would be appreciated. Thanks for the replies.

Edited by debusan

One other comment I would like to make is that my car is an AT/MT conversion. I am well aware that the AT harness has several pins that are not used by the MT or PFC ECU. But as far as I can tell from the wiring diagrams none of the pins in question are different between the AT and MT harness.

why are you using manual powerfc on auto car? you know its not supported right?

but anyway look at ETC, SENSOR SW CHECK and look at the values of MAFS-1 and TPS

do they both change at the same time?

I do see your point though The AT harness is heaps different and getting a MT harness may un-screw lots of these problems I have attached a shoddy video to show the symptoms on the hand paddle. I appreciate your help

http://www.youtube.com/watch?v=vl7LBBoAFRU&feature=youtu.be

FWIW, the fact that the car has been converted auto to manual shouldn't make any difference. You can run a manual engine with an auto ECU and vice versa. The car won't work well with a manual ecu in auto car because of lack of comms to the TCU, but that doesn't matter. What matters is that all sensors and outputs at the ECU that are involved in running the engine are same same.

It is entirely possible that you have a crossed wire, as we said earlier, or that your PFC has a severe problem. Can you swap in another PFC?

Yesterday I tried hard wiring the MAF into the Power FC I had the same result that was with me running all new wires straight from the PFC to the MAF. I don't have another Power FC and its a 1000$ to get another one in there. But if I must buy one then that is the answer. The traction control unit has been disabled. and the valve removed. so it should not be an issue.

Edited by debusan

So thanks to some info above I have uploaded a video of the PFC switch/test screen that shows the voltage issue in detail. I have a couple more things to check but I am starting to think that the PFC is the culprit as it is the only used part I installed in this car. Guess I need to fork over some cash then.

http://www.youtube.com/watch?v=H31n2YUQjyc&feature=youtu.be

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...