Jump to content
SAU Community

Recommended Posts

gday ive just got my new toy a c33 laurel and got it for a good price everything i want only problem is it is auto so will all know what the first thing that needs to be done what i need from some one that has maybe done this before and is in the now how is what parts i need to do this the car has a rb25 in it and i know parts for the laurels are hard to find i have found a few like dash cluster and gearbox its self and some interior parts but other things like what pedals can i use and are they the same as say a r33 or r32 if some one could give me a list of things i would need would be great

thanks

  • 2 weeks later...

gday ive just got my new toy a c33 laurel and got it for a good price everything i want only problem is it is auto so will all know what the first thing that needs to be done what i need from some one that has maybe done this before and is in the now how is what parts i need to do this the car has a rb25 in it and i know parts for the laurels are hard to find i have found a few like dash cluster and gearbox its self and some interior parts but other things like what pedals can i use and are they the same as say a r33 or r32 if some one could give me a list of things i would need would be great

thanks

I was going to do this on an A31 Cefiro but didnt. I did a bit of research etc and have an idea on what parts you need:

Box

Clutch

Master Cylinder

Tail shaft

Pedal box (I was told an R32 pedal box would fit in the ceffy so its likely to fit the C33)

Hand brake assembly (my ceffy has the old school foot brake)

Shouldnt have to change ECU etc as to my knowledge these run independent boxes.

I think thats about it from memory. Hope this helps

Yes the pedal box fits both A31 and C33, you also need a manual brake pedal (narrower), and manual footrest (also not as wide as the auto item)

Auto transmission is run on an independent ECU, which is located in the driver's side kick panel, the engine ECU will run fine without it. The only part you need to worry about there is rigging up the neutral-position sensor, or bridging the connector, to trick the car into starting, otherwise it will won't think it's in park/neutral and the starter circuit doesn't work.

Yes the pedal box fits both A31 and C33, you also need a manual brake pedal (narrower), and manual footrest (also not as wide as the auto item)

Auto transmission is run on an independent ECU, which is located in the driver's side kick panel, the engine ECU will run fine without it. The only part you need to worry about there is rigging up the neutral-position sensor, or bridging the connector, to trick the car into starting, otherwise it will won't think it's in park/neutral and the starter circuit doesn't work.

So the box has its own ECU? is that then connected to the engine ECU or its just on its own?

Everything between Cefiro and Laurel is interchangeable except rear door cards, glass and fixed body panels.

They're the exact same chassis with a different shell on them.

Is that right? I didnt know that. Good news as I may be wrecking a ceffy soon (if it doesnt sell) and if parts fit on Laurel, well that means bigger potential market for me.

really thats a sore i can relax on the manual interior parts now and just have to sort tail shaft and crossmember out ive read that crossmember 'B' is the one to use and have checked my mates crossmember on his factory manual c33 and it is a B but will it fix with the 25 box thats the question fingers crossed as we both are about to take on the same things

Everything between Cefiro and Laurel is interchangeable except rear door cards, glass and fixed body panels.

They're the exact same chassis with a different shell on them.

Does this apply to C33, C34 and C35 Laurels?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...