Jump to content
SAU Community

Recommended Posts

Hi besides the Nittos and BF goodrich tyres are there any other good drag radial tyres avaliable, looking at the HPI list the BFG are becoming the leaders in the rwd classes.

Currently im looking at getting the BFG comp t/a in 255/50/16 just looking for some other options that are avaliable locally in a 16'' preferably

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/
Share on other sites

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

I think you can get Hoosiers in a 17" but that doesnt help much and i am not sure where they come from :P

BF's are newer and i am sure they benefit from more development. The 60's tend to show it.

I am more than happy with my Nittos. Can't wait to see how the new 275's go this saturday!

Adrian

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/#findComment-858890
Share on other sites

MT Et streets are not in the HPI rules are they? keir wilsons car isnt listed with his 8sec pass but there are BFGs on the list, i was going to go for something like the ets but when the BFGs are as good as they seem and still qualify for the HPI llist they seen better

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/#findComment-861849
Share on other sites

MT ET Streets are cross-ply. They're not allowed under the HPI rules. They have to be radials. ET Street's are just a slick with a few pissy little lines on them! Nittos/BFG radials look like conventional road tyres.

Nittos aren't too bad in the wet too, so I found out yesterday. On 10 pounds boost mind you.

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/#findComment-863225
Share on other sites

  • 2 weeks later...

There were plenty of historic muslce cars that came factory equiped with crossply tyres. So I reckon excluding them from the street tyre class is dumb. What about cars with modified panels or wheel tubs or instant coffee machines or an aftermarket albatros?

Go fast or go home.

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/#findComment-878805
Share on other sites

Yep I think they were trying to copy the street tyre class in Japan, I don't think its that silly as it keeps the mini tubbed rotors out of the class and is as close as you'll get to a real street trim class for imports

And with the times and 60ft's people are pulling off with Radial tyres now, I don't really think it causes to big a problem if your cars set up right

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/#findComment-881199
Share on other sites

Yep I think they were trying to copy the street tyre class in Japan, I don't think its that silly as it keeps the mini tubbed rotors out of the class and is as close as you'll get to a real street trim class for imports

And with the times and 60ft's people are pulling off with Radial tyres now, I don't really think it causes to big a problem if your cars set up right

It doesn't make sense at all.

I don't see why we need to copy anything japan does with regards to rules either.

As for keeping it as close to a 'real street trim class for imports' there is no substance behind that at all. It's all too subjective. I'd like to know what excludes these tyres from being called street trim appart from the 'japs don't do it' argument.

I guess if you care what HPI publish you can try to make it into their list following the jap way. To each thier own. I personally care more about going quick than whether a Magazine I don't read publishes my time. Things change so maybe HPI will make the list more interesting by opening it up to all street tyres one day, I mean part of chasing the better times with better tyres is about safety too.

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/#findComment-881614
Share on other sites

There's a fugen huge difference btw an ET Street and a Nitto NT555R! I have driven through all manner of shitty wet weather with my Nittos and they are just as good as any other road tyre I've used in recent times. Stuffed if I'd try doing it on ET Streets! A couple of pissy little lines aren't what I'd call tread. Hence ET's aren't a road tyre in my book.

I'd say you'd have a fair chance of the law wanting to know all about your ET Streets too. By comparision Nittos are the most conventional looking road rubber out of all the semi-comps.

ET Streets - from the land of road legal Nitrous and drag slicks with grooves :)

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/#findComment-882947
Share on other sites

I dont call ET streets a street tyre. If a cop pulled you over with them on, try and expalin them to him! Plus I doubt they would be any good in the wet.

What about the Sportsman Pro's?

1.56 60ft with an 8" wide sportsman pro. 460hp at flywheel. Picks up the front left on take off. Not a skyline, but standard setup RWD (no four-link, tubs etc)

Plenty of tread (ugly looking read though), and pretty good in the wet.

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/#findComment-883028
Share on other sites

What about the Sportsman Pro's?

SERIOUSLY considered these tyres but wanted to go a pair of radials first and then just run slicks.

Look like the business for sure. Too soft to drive regularly on the road though and expect decent mileage.

Adrian

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/#findComment-883366
Share on other sites

So you really consider a Mickey Thompson ET Street a street tyre you could drive around on every day of the week?

You could but, like most very soft compound tyres it will cost a few dollars to support the habit plus they are crap for wet weather and really do their best job going straight.

Friends and I have in the past driven around the streets on them, so there you go.Got pulled over by the cops in a hot rod with a set of Mickey T's on the back once and they mentioned the tread getting a bit low to us but, didn't have a problem with them. Also, I don't think you need to look too far to see some of the guys at the street meet drags who actually will drive home on them.

I think if you only want to have one set of rims and tyres then you must compromise a little. It is this case that makes the Mickey T's and others a bad choice for many. Having said that by definition they are a road tyre, I know of enough cars that drive on them (even if it is only a sunny sunday) for me to accept a beating by someone running these tyres without a winge about ' ooh it's not fair you cheated becasue they aren't real street tyres...nah nah nah..'

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/#findComment-883750
Share on other sites

Ahh well lucky most of us on the forum seem happy with the HPI rules, no matter how silly it seems to others and with some of the 60ft's I've seen from the rwd imports 1.6-1.7 I really don't think it will hold anyone back unless they want a reason to whinge or an excuse as to why it didn't happen for them, In short if there car is set us right and they have the power they claim they do a radial tyre will do fine :)

Link to comment
https://www.sau.com.au/forums/topic/41949-drag-radials/#findComment-883845
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...