Jump to content
SAU Community

Recommended Posts

Just need some wisdom on an issue that has been bugging me. I had a tune done by Boostworx in Adelaide back in early Jan 2013. Wen I drove it from Wagga to Adl it ran back on 5 cyl due to a coil pack failing. As a result the plugs fouled out due to incorrect gapping done by a mechanic in Wagga. They still profess to say the gap is meant to be 1.1 according to there books but I know its meant to be .75, .8.

Replaced a coil pack with a standard one upon arrival in Adl and then when the hot weather came in I dropped another coil but only once the car got warmer. Drove back to Wagga and 10 hours later another coil seems to have spat it.

Dilemma I have is I was informed by a few mechanic that the standard genuine coil packs provide a better spark and make the car run better. Do i creplace all coil packs with standards or move on? Is the issue more then coil packs even though I have replaced plugs again with correct gapping done by boostworx.

Any help would greatly be appreciated.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/419567-coil-pack-issue/
Share on other sites

Hi mate, 1.1 is the correct gap for skyline plugs, so don't blame the local guy. Where that gets tricky is that you may need to lower the gap to get a consistent spark with older coil packs, higher boost etc etc.

You should always run the largest gap you can (without missfire) to get the most efficient burn due to the largest spark.

As for coil packs....in my experience, any new set will provide a better spark than a 20yo set. While some people have had Dead on Arrival (DOA) issues with cheaper coilpacks, if they work they will work as well as factory. And pretty much any supplier will replace a DOA coil pack (not to mention they have to under fair trading laws)

Link to comment
https://www.sau.com.au/forums/topic/419567-coil-pack-issue/#findComment-6743146
Share on other sites

in these Forums the most common advice on Gap and coils is Splitfire and 0.8.

taking note most of the skylines are modified as Duncan pointed out

Stock - I'm sure Nissan has it right on the money.

Plugs and coil pack replacement is easy so save money and do it yourself.

I would not replace a single coil pack unless it was one of a full new set.

If your having one old one fail then another take the leap and do all six new at once.

Link to comment
https://www.sau.com.au/forums/topic/419567-coil-pack-issue/#findComment-6743185
Share on other sites

rathy, as stated, that is what it would say in any spark plug suppliers book.

they would also have platinum tipped spark plugs as the replacement.

tuners will generally swap the spark plugs back to a standard plug for greater surfave area on the tips.

gap them down(ive run 0.7mm in the past) and tune accordingly.

there is also a debate on the best coil packs.

any new set will generally creat a better spark than your 20yr old set.

alot seem to think brand new nissan to be one of the best.

you pay with blood for these, so alot dont care for them.

there could also be other reasons for dropping a cylinder.

get it checked by your mechanic.

good luck, and keep us updated.

Link to comment
https://www.sau.com.au/forums/topic/419567-coil-pack-issue/#findComment-6743924
Share on other sites

Red hot! Thanks for the reply fellas. I have gone with a colder rating plug and had them set to .75 and ordered a new set of coil packs. Easier to replace them all then one by one.

Didn't mean to blame the mechanic but the plugs only lasted one long trip but did get money back for them, Will see how it travels over the next coming weeks when these new packs arrive.

Cheers once again!

Link to comment
https://www.sau.com.au/forums/topic/419567-coil-pack-issue/#findComment-6744390
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...