Jump to content
SAU Community

Yellow Jackets Ignitor Modules - S13/s14/180Sx & 300Zx/r32-R33 Gtst - Testers Needed.


Recommended Posts

Hi Guys,

I am about to release the latest addition to our Yellow Jackets product range:
Ignitor module - S13/S14 SR20DET
Suits:
SILVIA/200SX - PS13/KPS13 - 2.0L - SR20DET (1991-1993)
SILVIA/200SX - S14/CS14 - 2.0L - SR20DET (1993-1999)
180SX - RPS13/KRPS13 - 2.0L - SR20DET - (1991+)

Ignitor module - Z32 300ZX/R32 GTS(T)/R33 GTS(T)

Suits:


300ZX Z32 - 3.0L - VG30DE (01/94-8/96)
300ZX Z32 - 3.0L - VG30DETT (01/94-8/96)

Skyline R32 GTST/4 - 2.0L - RB20DET (05/89-7/93)
Skyline R32 GTS25 - 2.5L - RB25DE (08/91-8/93)
Skyline R33 GTS - 2.5L - RB25DE (08/93-5/95)
Skyline R33 GTST - 2.5L - RB25DET (08/93-5/95)
Maxima from 90-91
Maxima GXE from 92-94
Maxima SE from 92-94
Infinty J30 VG30DE from 93-97

At this point we have carried out tests on equipment with good results but traditionally I like them to be tested in real-life situations before releasing them to the market.

Please PM me if you are interested.

Cheers,
P-W.

I will be interested to help you out, test them fully and post results.

But bear in mind I did have red jackets which lasted 5 dyno pulls before they stuffed. So I hope this is a split fire equivalent rather then different colour same sht.

I will be happy to send them back to you after trailing, but not interested of paying for them.

Are these only suitable for stock/mild power applications?

Curious as to why you have excluded R32/R33 GTRs

These are designed to replace the stock ones that eventually fail and at a cheaper price.

We havent gotten around to doing the R32 GTR ones yet.

Why do you have a car listed (R34 GTT) that doesn't need an ignitor module?

whoops. my bad.

I'm keen to give them a go, what sort of current can they handle? I currently run Bosch mec723 coils on a link ecu. I am running twin r33 igniters in parallel this enables me to run the coils up to full dwell. (About 9 amps). Problem I have is the link has only 3 ignition drives, so it is triggering two coils at a time doubling the current (18amps).

Do you have any higher rated igniters?

Hi,

I did testing for your yellow jacket coils in my r32 a couple of years back. They are still going strong and id like to assist with test for these also.

As before a can provide back to back testing and have easy access to a dyno.

Please let me know,

Looking forward to hearing from you,

Regards,

Ashley Smith

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...