Jump to content
SAU Community

Wrecking Rb25Det S1 Engine All Parts Available

SIFTY32

By SIFTY32,
in Classifieds

 Share

Recommended Posts

SIFTY32 Proficient

SIFTY32

Posted
Posted

Hi guys I have a complete rb25det series 1 engine here that I'm stripping for parts, almost everything is there and for sale the only thing I am keeping is the long engine



Ill post a few prices up but pm me for a price on anything else...



rb25det ecu - $130



rb25det s1 turbo arguably zero shaft play - $250



rb25det cas - $90



rb25det coilpacks - $130



rb25det igniter - $80



rb25det alternator - $70



rb25det ps pump - $70



rb25det a/c compressor - $90



rb25det exhaust manifold - $50



rb25det hamronic balancer mint no chips - $70



rb25det coilpack loom mint - $100



also I have a rb25 head bolted to a rb30 block (rb25/30) still needs the mods done to make it run and the block should be freshened up but the main bits are there - $400



some price are slightly neg but no low ballers please :)



located in algester 4115 but will post at buyers cost



contact 0420 767 957



Cheers

  • 2 weeks later...
  • 2 weeks later...
  • 4 months later...
  • 3 weeks later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Lithium
      Garrett G Series

      By Lithium · Posted

      Oof. One of my mates has an R34 GT-R that he initially was a "I want to go twins for response and convenience" on his stock 2.6 with Kelford 272 cams, but his friends are pests and were always in his ear about their place being in the bin.   Eventually one of the 2860-5s decided to add it's own input and force his hand, so he conceded and went for a Pulsar 6262G ("G35 900") with T4 0.85 hotside.    Here's an overlay of the results, same cams, same stock bottom end, same boost, same fuel, just from a pretty tidy 2860-5 install to a Pulsar turbo on a 6boost maniifold on BP98.   Worth mentioning here, it may seem like a dead horse thing but the dyno plot doesn't tell the story of how much better it is to drive - transient response has completely changed the car, he used to have flat foot shifting to stop it having to wind up again on gear changes even at >7000rpm... now it builds boost faster than that even short shifting.   It's 100% transformed the car before you even consider how much better it holds on: Pulsar and Garrett aren't the same, but from our experience if you're just looking for a better drive and the ability to make the same or more power I think the divided G30 770 would probably be the smallest I'd go to.
    • robbo_rb180
      Neil's R33 Gts-t Build

      By robbo_rb180 · Posted

      Great work Duncan, any events local you will give it a test once all done? 
    • robbo_rb180
      Rob's S Chassis track cars. Now with more s15 and less 180sx

      By robbo_rb180 · Posted

      Sweet, yeah hoping stock gears will hold up. May use the transbrake feature on hill climb starts so that will test it.
    • GTSBoy
      What Bucket Seats Do You Have In Your R34 Gtt?

      By GTSBoy · Posted

      Yeah, the thread is only nearly 20 years old.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      Been down in Tassie for 2 weeks (a cruise, not a race for once) but spent a little time on her when I got back. I worked out the injector settings in the PowerFC were not correct for nismo 555s, set those to 66% +10ms and added a little air at closed throttle, set the timing (approximately, because it has some weird non 15o cells around idle) and now she starts and idles properly. She purrs like a kitten (ignore the co2 alarm in the background, I did  ) 20250518_171052.mp4 Next step, off for run-in, tuning and alignment!
×
×
  • Create New...