Jump to content
SAU Community

Wrecking Rb25Det S1 Engine All Parts Available

SIFTY32

By SIFTY32,
in Classifieds

 Share

Recommended Posts

SIFTY32 Proficient

SIFTY32

Posted
Posted

Hi guys I have a complete rb25det series 1 engine here that I'm stripping for parts, almost everything is there and for sale the only thing I am keeping is the long engine



Ill post a few prices up but pm me for a price on anything else...



rb25det ecu - $130



rb25det s1 turbo arguably zero shaft play - $250



rb25det cas - $90



rb25det coilpacks - $130



rb25det igniter - $80



rb25det alternator - $70



rb25det ps pump - $70



rb25det a/c compressor - $90



rb25det exhaust manifold - $50



rb25det hamronic balancer mint no chips - $70



rb25det coilpack loom mint - $100



also I have a rb25 head bolted to a rb30 block (rb25/30) still needs the mods done to make it run and the block should be freshened up but the main bits are there - $400



some price are slightly neg but no low ballers please :)



located in algester 4115 but will post at buyers cost



contact 0420 767 957



Cheers

  • 2 weeks later...
  • 2 weeks later...
  • 4 months later...
  • 3 weeks later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...