Jump to content
SAU Community

Recommended Posts

Hey Guys,

I have a few stagea questions for the techs.

I have had cefiros, skylines etc but i got into motocross a few year ago so i downgraded to a old 88 triton..

recently i purchased a car i have wanted for a long time, a Stagea.

i have had it for a week today and i have a few questions for yas.

1.)Is there an over driver on and off switch for the automatic transmission??

2.) i always let it warm up before i drive, if i let it warm up for 2 minutes 30 seconds ( temp gauge goes to half way) is fine, but if i let it warm up for 30 seconds ( temp gauge hasn't moved) it cuts out??

3.) last night the AT light came on the dash and car wouldnt go into over drive, pulled over, turned car off then it was fine??

any ideas would be great guys

cheers

Kris

Link to comment
https://www.sau.com.au/forums/topic/420632-stagea-problems-please-helllp/
Share on other sites

Ok so it happened again. Driving today and AT ligjt came on . So I pulled over. Instead ogf turning on and off I stopped and took off again. It was like it was in 4th and was stuck. Sounded like it was slipoing but once I got speed was fine. The dash said it was changing gears but didnt feel like it.. so I stopped and turned it off again. Now its fine again . Does this soumd like somethibg major??? Just sucks coz cant get it to mechanics for another 3 weeks

I've only ever had a S1. I don't think you guys are talking about the O/D though, but the torque converter locking up after warming up. It'll go into O/D when cold but the converter won't lock up until the box reaches temp (kind of sounds like going into another gear though I guess). In winter I can almost get home before it'll lock up. But I don't think thats the problem here anyway. I don't know if the S2's have the A/T switch to go between power, normal and snow. But flicking it in snow will make it feel like that. Takes off in second from stand still. But I'm thinking its going into a limp mode for the gearbox. So could just be a sensor somewhere that on its way out or something more sinister. Explains why when you turn the car on and off it goes away.

As a suggestion, do this:

http://www.skylinesaustralia.com/forums/topic/266512-reading-nissan-fault-codes-ecu-fault-codes-how-read-them/

Have pen & paper ready.

It should give you an indication as to what could be at fault.

Clear the codes & see what happens. Sometimes, if there is a minor hiccup (e.g. slightly ill fitting harness plug) in a system somewhere, it logs a code. Even if the hiccup disappears, the code is still logged, so it can bring the light on & depending on how bad the ECU thinks the issue is, go into limp mode, like what's happening to you.

While this sounds more like a faulty sensor, have you checked trans fluid level? I know autos can get all funky when they are low.

And for christ's sake, don't warm up your car for two and a half minutes >< You're doing more harm than good.

Start it

Let it idle for 20-30 tops

Get going

Drive sedately until it's up to temp

ah ok fair enough then...

i only let it warm up that much once, usually is about 30 seconds, trans fluid looks ok but will double check levels tongiht i guess. going in to get checked soon i hope

Taking it to a work shop tonight hopefully. they didnt have the connections to run the tests last night so hopefully they have them today.

its been fine, the mechnic told me togive it a bit and i do today and the AT light came on twice =(, i had more of a play around and it seems to come on, ans be stuck in 3rd and 4th, and when its in 4th i decellerate drops to 500 rpm, again turn it off and fine, hopefully they can source the prolem today.

Hey guys, got it scanned today and its shift s/v a psw, so the shift solenoid has shit itself.

they quoted $500 approx not including oil etc..

anyone replaced one before? i know the sump has tto come out bud dunno what else has to be done

They would have to drop the valve body to replace the solenoid, $500 is a little expensive, but they did diagnose the fault and they need to warrant their work. If it fixes the fault I guess you got out of it cheap, a s/h box would cost a lot more than that fitted...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...