Jump to content
SAU Community

Recommended Posts

Hey guys originally I was after a tomei oil pump and still really considering one but I've been offered a jun pump for a pretty decent price just depending if he accepts my offer, are they a good oil pump to use ? Any down sides of it compared to the tomei, the more answers the better

Cheers

I have a little bit by the looks of it tomei is too good, I've searched that some of these have shattered

I know of two tomei pumps that have failed - but there was no information as to why they failed (could have a been a crappy install, eaten engine block etc). By all reports Tomei is great pump and these isolated failures shouldn't put you off.

The nitto pump is another great peice of engineering. As far as i'm aware, there has been no reported failures thus far for these. And they have been known to eat engine block and survive :-) Mine is going great :-)

Haven't heard much about the JUN pumps. I know they have been used in some high HP car's with no drama's.

Edited by wedge_r34gtr

I've got the Jun pump in my RB28, making over 600rwhp, limiter bashed regularly etc etc still going strong...but I think you'll hear that about all the name brand pumps.

So Jun, Tomei, Nitto,etc all a big improvement over the standard one, take your pick.

Tomei is the best - simply by design.

The others, all a case of how much do you want to spend. No-one can decide that for you.

That's not to say they are a bad pump, just not the best.

Give any muppet a pump (or a bad build), and any oil pump can be destroyed. Tomei/Nitto/JUN or otherwise.

Tomei or Nitto, i'm not sure if Nitto has released their new Spline drive pump or not yet, if they have, get one of those!

The most important thing to make sure you do is fit a crank collar that gives the correct collar to pump drive flat clearance.

I have a Nitto pump and collar on my engine, i came to that decision after months of research.

If i were to do it all again for a track oriented vehicle it would be an external belt driven pump, either wet or dry sump.

I have a JUN, had no problems and I don't think I ever will.. Tomei is probably the best and I'd buy one if I had to choose again

As stated above, any pump will eventually fail if rev limit bashed enough/bad harmonics or wrong collar clearances

I've been using Jun pumps for years on the OS giken engine without problem.

Willall racing drag car also used this pump with revs of 10,000+ rpm without any pump issues.

If you can pick it up for under 1k...then that is a steal!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...